User manual OKI GL412E ACCESSORY INSTRUCTION GUIDE

[. . . ] Indicates a potentially hazardous situation which, if not avoided, may result in damage to your product or host equipment. NOTE!Emphasizes useful tips or recommendations for efficient and smooth operation of your printer. 3 LAN Card Installation Guide 1. 4 . Contact and Document Information SATO GROUP OF COMPANIES International Headquarters SATO INTERNATIONAL PTE. LTD 438A Alexandra Road #05-01/04, Alexandra Technopark, Singapore 119967 Phone: 65-6271-2122 Fax : 65-6271-2151 Email: sales@sato-int. com Americas SATO INTERNATIONAL AMERICA, INC. [. . . ] Refer to the Operator's Manual for the procedure to configure the LAN settings. A summary of this procedure is reproduced on the following page, but the Operator's Manual contains further details in the section on Interfaces Mode (See page 4-52 and subsequent pages). Figure 1. Removing the interface cover plate and installing the LAN interface card 5 LAN Card Installation Guide LAN CONFIGURATION FOR ETHERNET CONNECTION Once the LAN card is installed, you can access the Ethernet settings in the GL's Interfaces Mode menu. An overview of the LAN options is listed below, followed by explanations of relevant LCD menu options in the following pages. POWER ONLINE INTERFACES PARL / SBPL Host Interface* Host Interface Auto Switching* OFFLINE INTERFACES Host Interface* Host Interface Ethernet* LINE INTERFACES ETHERNET PORT ENTER ETHERNET PORT INTERFACES Timeout Timeout 10 sec* Interface Mode ENTER Switch Out On Data Timeout* INTERFACES Ignore CR/LF Item No. Protocol Host Interface ETHERNET PORT ETHERNET ADDRESS ETHERNET SETTING Parallel Port USB Port Serial Port Printer Mgt Screens only display if Admin User is enabled within the Advanced Mode No* Item No. Protocol Status 5* Host Interface Auto Switching* DHCP Disable* MAC Address XXX. XXX. XXX. XXX Offline Process Disable* Gateway Address XXX. XXX. XXX. XXX Job Control Standard* INTERFACES ETHERNET SETTING ETHERNET SETTING ETHERNET ADDRESS IP Address Subnet Mask Gateway Address MAC Address DHCP NetBIOS Protocol NetBIOS Protocol Enable* ASCII Data Port IP Address XXX. XXX. XXX. XXX 1024* Keep Alive Timer Subnet Mask XXX. XXX. XXX. XXX Ethernet Speed Auto Select* 3 minutes* Ignore CR/LF ENTER Ignore CR/LF Figure 2. Overview of the Interfaces Mode menu for LAN configuration 6 LAN Card Installation Guide The following tables explain the relevant options available via the LCD screen in Interfaces Mode. Menu screen What the options mean Is the menu selection screen for the Host Interface option of the INTERFACES mode. INTERFACES Host Interface* There are only two options relative to the serial interface, ignore all others. Host Interface Auto Switching* · Auto Switching - the printer automatically switches to the relative interface type and moves into the applicable menus. Allows the operator to select the interface and the relative menus will follow. Is the menu selection screen for the Ethernet Port option of the INTERFACES mode. INTERFACES ETHERNET PORT Is a menu subset of the Ethernet Port option. Will move into the Timeout menu. ETHERNET PORT Timeout Timeout 10 sec* This is the value used by the printer to time out from the current port and check the other selected Port Types for data print. When the printer has not received data from the host after a certain period of time, it must timeout in order to service other ports. The factory default of 10 seconds with an allowable range of 1 to 60 seconds. Determines when other ports are active and able to communicate with the printer when the Ethernet interface is not in use. Switch Out On Data Timeout* · Data Timeout - factory default. The other ports (Parallel, Serial, USB) are able to send data to the printer when the timeout setting has been reached. [. . . ] The NIC card is simply a pass-trough and the printer tells the host when the job is complete. Determines whether the printer processes incoming data when it is in an offline state. Offline Process Disable* Ethernet Speed Auto Select* Job Control Standard* · Disable - factory default. Note: When changing the Gateway Address, the printer resets the NIC when the printer is place online. [. . . ]