User manual OKI ES3037ECCS

[. . . ] Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this Guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer. [. . . ] Press the VALUE button until ALL JOBS or the required job name is displayed. Press the CANCEL button to delete the remaining copies of the document. When the deletion confirmation message appears, confirm by pressing the SELECT button. ES 3037/3037e Operation · 116 Store To Hard Disk Store to HDD (job spooling) allows print jobs to be temporarily stored on the hard disk before printing. NOTES · The internal hard disk must be installed in the printer and enabled to allow for spooling of the print job before final printing. · If the hard disk memory is insufficient for the spooled data, DISK FULL is displayed and only one copy printed. · If the software application being used has a collate print option, this must be turned OFF for store to hard disk to operate correctly. · Store to hard disk may not be available in some software applications. 1. Enter a job name of up to 16 characters under Job Name and a four digit personal ID number. The document will be stored on the printer's hard disk. ES 3037/3037e Operation · 117 4. The document can then be printed or deleted using the procedures given below. Printing copies MENU ITEM VALUE SELECT 0 ON LINE 1 5 2 6 PrinterMenu. eps 3 CANCEL 4 7 1. Press the MENU button to access the PRINT JOBS MENU and press the SELECT button. Enter the personal ID number you selected above using the buttons on the printer control panel. Press the VALUE button until ALL JOBS or the required job name is displayed. Press the MENU button to access the PRINT JOBS MENU and press the SELECT button. Enter the personal ID number you selected above using the buttons on the printer control panel. Press the VALUE button until ALL JOBS or the required job name is displayed. Press the CANCEL button to delete the remaining copies of the document. When the deletion confirmation message appears, confirm by pressing the SELECT button. Run Maintenance Cycle Before Printing This option allows you to improve your print quality if you suspect there is a problem with printing, such as too much graininess in the print. ES 3037/3037e Operation · 118 1. Select Run Maintenance Cycle Before Printing to force the printer to automatically clean itself before printing. ES 3037/3037e Operation · 119 GENERAL PRINTING DIRECTIONS What follows are descriptions of common printing issues common to the Macintosh environment. This section does not attempt to cover all the options that might occur, but rather, the typical printing operations that can benefit from detailed descriptions. You can also refer to your Macintosh online help or manual for further information. Multiple Pages on One Sheet 1. Then open the drop-down menu directly underneath the printer and select Layout. Layout. jpg ES 3037/3037e Operation · 120 3. [. . . ] · Press ONLINE to place the printer back online. FINISHER The Finisher allows you to staple, punch and offset the printed documents emerging from your printer. The accessories available are: · Finisher with 2 hole punching · Finisher with 4 hole punching · Finisher Interface Kit · Finisher Stand For full details, refer to the Finisher User's Guide. ES 3037/3037e Accessories · 237 Specifications Print method LED exposed light source electronic photographic memory ES 3037 - 600x1200 dpi ES 3037e - 1200x1200 dpi Cyan, magenta, yellow, black (CMYK) ES 3037: 450 MHz, ES 3037e: 600 MHz Resolution Colors Processor speed Memory ES 3037 - 128 MB standard Extra memory may be required with Duplex unit ES 3037e - 320 MB standard Up to 1 Gb max with optional memory modules Capacity - 10 MB PostScript3, PCL5c Epson FX and IBM ProPrinter dot matrix emulations Windows XP, 2000, Me, 98, 95, NT 4. 0 MacOS 8. 6 - 9. x, Mac OS X (10. 1 and above), Classic PostScript 3, PCL5c fonts First print time: 10 secs (black) First print time: 11. 5 secs (color) Warm up time: 160 secs HDD Emulations Operating platforms Internal fonts Time to Print Start ES 3037/3037e Specifications · 238 Parallel Interface Designation: IEEE-1284 Connection: 36-pin, IEEE 1284-compliant Required cable:Standard bi-directional IEEE-1284 compatible cable of up to 6 ft. Must comply with FCC regulations, must be shielded with twisted pair conductors, and must be UL and CSA approved. Transmission modes: Compatible, Nibble, ECP Interface level: low = +0. 0 to 0. 8V, high = +2. 4 to 5. 0V Designation: USB specification Version 1. 1 Connection: USB Type B Required cable: Shielded, USB specification Version 1. 1 Transmission mode:Full speed (12 Mbps + 25% maximum) Power control: self powered device 100BASE-TX/10BASE-T (option) Color: letter = 30 ppm, tabloid = 16 ppm Monochrome: letter = 37 ppm, tabloid = 20 ppm Transparencies, color: letter = 10 ppm Paper tray, manual feed, optional additional paper tray(s), optional high capacity feeder Letter, Legal-14, Legal-13. 5, Legal-13 Tabloid, Tabloid Extra, Executive A3, A3 Nobi, A3 Wide, A4, A5, B4, B5 A6 (Tray 1 only) Universal Serial Bus (USB) interface Network Print speed in pages per minute (ppm)a Paper feedb Media size Trays 1 thru 5 a b Print speed varies with paper size, media weight and paper feed. [. . . ]