User manual OKI B4600NPS SETUP GUIDE

[. . . ] IBM, Proprinter XL, Proprinter, and IBM/PC are registered trademarks of International Business Machines Corporation. Intellifont is a registered trademark of AGFA Corporation, a division of Miles, Inc. Microsoft and MS-DOS are registered trademarks of Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. [. . . ] Select the setting menu and enter the sub-setting menu to change the settings as follows: s Execute Data Note This menu appears only when data has been saved on the card. When you select "EXECUTE DATA, " you can execute any of the data saved in the SAVE DATA mode. When you enter this sub-setting menu with the SET switch, the printer prompts you to select the ID of the data. DATA ID=##### Select the ID with the v or w switch and press the SET switch again, so that the printer executes the selected data. 4­34 CHAPTER 4 CONTROL PANEL s Card List When you select "CARD LIST" and you press the SET switch, the printer automatically loads paper and starts printing the contents of the installed flash memory card or HDD card. s Save When you select "SAVE" and you press the SET switch, you can enter the following sub-setting menus to save the macros and fonts in the installed card: Display Message Save Menu Save data that the printer will receive and set its ID. This menu appears only in the HP LaserJet 4+ emulation mode and BR-Script 2 mode. SAVE DATA SAVE MACRO PRIMARY FONT SECONDARY FONT DOWNLOAD FONT Note If the capacity of the card becomes low while macros and fonts are being saved, the display shows the "CARD FULL" error message and they cannot be saved. The CARD LIST displays the contents and the used capacity. 4­35 USER'S GUIDE · Save Data You can send data and save it on the card. In this mode, any kind of data such as PCL data, BR-Script 2 data, and command strings can be saved. When you select "SAVE DATA" and you press the SET switch, the display shows the following guide menus. SET KEY --> END This message prompts you to press the SET switch again so that the printer exits from the data reception status when you finish sending data. Notes When you send data to be saved on the card, it is temporarily stored in the RAM of the printer. Note the following: · If the received data exceeds the RAM capacity, a memory full error occurs. When this error occurs, only part of the image has been stored in RAM, therefore, you cannot save the data to the card. As not all the font data has been stored in RAM, you cannot save the font to the card. When the font data is saved, the printer is reset to ensure as much capacity as possible in RAM. · If you have saved the font at 600-dpi resolution and change the printer resolution to 300 dpi, the printer cannot print the saved font. 4­38 CHAPTER 4 CONTROL PANEL · Download Font Notes · The "DOWNLOAD FONT" menu appears only in the HP LaserJet 4+ emulation mode. · Be sure to print out the list of download fonts with the TEST switch and check the download font ID on the list before you enter this menu. You need to select the font in this menu with the same number you see on the list. If you have downloaded a font into the printer memory, you can save it on the flash memory card or the HDD card. The printer prompts you to select the download font ID that you can find from the font list. Press the SET switch to move the cursor to the ID and select it with the v or w switch. FONT ID=##### Note The download font IDs do not appear when fonts have not been downloaded. After you select the download font ID, press the SET switch, so that the printer saves the selected download font. Vector or bitmapped fonts are saved in the format of the original font. Once you save the download font in the card, you do not need to download the font every time you need it. [. . . ] s Expanded Character Width, Line Block Drawing & Box Drawing n = "wnnn" or "Wnnn" Expanded character © 1. 2 mm Line Block Drawing & Box Drawing © 1 dot This parameter specifies the width of expanded characters as above. Appendix­69 USER'S GUIDE s Expanded Character Rotation n = "a0" or "A1" n = "a1" or "A1" n = "a2" or "A2" n = "a3" or "A3" s Bar Code Data Start n = "b" or "B" Data that follows "b" or "B" is read in as bar code data. Bar code data must end with the " \ " code (5CH), which also terminates this command. The acceptable bar code data is subject to the bar code mode selected by "t" or "T". · When CODE 39 is selected with the parameter "t0" or "T0": Forty three characters "0" to "9", "A" to "Z", "-", " . [. . . ]