User manual OK BABY SIRIUS

[. . . ] The material of the seat (polypropylene) loses some of its mechanical properties with the ageing process, if exposed for a long period to the effects of the environment (sun, rain, ice etc. ). In the case of normal use and exposure to environmental effects, the seat should be replaced after three years. Always remove the seat from the bicycle if it is carried on the roof of a car or in a bicycle carrier. Resistance of the air could ruin the seat or remove it from the bicycle. [. . . ] 1 Seat 2 Padding (cover with Velcro system) 3 Safety belts 4 Footrests with respective belts and regulating pin 5 Support arm 6 Reflector 7 Fixing counter-block 8 Fixing block 9 4 long screws with respective nuts and Allen wrench 10 5 plastic adapters for different frame widths 11 Fixing counter-block protective cover 12 Plastic fixing plate 13 Fixing bridge of the support arm with relative screws 14 Fastening cover 15 Metal support 16 Knob for inclination of backrest 14 6 1 2 3 5 8 7 11 15 10 9 4 12 16 13 Fig. : Supply of OKBABY child's bicycle seat Instructions for use and assembly LIB006R05 Edition: 05-2005 Chapter 4/5 ENGLISH Child's bicycle seat OKBABY SIRIUS Page 66 Chapter 6 Child's bicycle seat OKBABY SIRIUS Page 67 ENGLISH 4 Product description 6 Mounting and assembling the seat The seat is suitable for cycles with 26"/28" wheels and frames with a round section diameter of 28-40 mm. It cannot be mounted on frames of a different diameter or on oval or square section frames. In this case, dismount and replace the carrier with a narrower model before mounting the seat. The child's seat is fitted with an "A. B. S. " system adjusting the inclination. We invented and patented this system (Automatic Barycentre System) in order to automatically keep the centre of gravity in the right position on the bike wheel axis, making it even safer for you to transport your child. Contact the manufacturer if you are not sure whether the seat is suitable for your bicycle. WARNING!Follow the safety warnings (see Chapter 1) to avoid injury or damage due to assembly mounting errors!IMPORTANT/NOTE: The numbers in brackets refer to chapter 3 "Product overview". IMPORTANT/NOTE: Whilst fixing the seat to the bicycle, take care not to damage or trap any brake wires or wires of the bicycle's electrical system. Step 3: Close the fixing cover (14) and slide it upwards to hook on the safety lever 24. If the cover opens, the child may be moved forward and unbalance the person riding the bicycle. 14 5 Signs and symbols 15 Chapter 6 describes the assembly and chapter 7 the fundamental use of the bicycle seat. Read these chapters carefully to understand and put the possibilities and functions into practice. The following terms and symbols are used: Symbol Term DANGER WARNING ATTENTION Meaning Warning of possible serious or fatal injury to people Warning of possible slight injury to people or damage to things Warning of possible defects and/or destruction of the product An important or useful note is provided 24 24 Illustration 2: Tilt the backrest as far as it will go pressing downwards and at the same time rotating the knob (16). IIMPORTANT/NOTE 16 Instructions for use and assembly LIB006R05 Edition: 05-2005 Instructions for use and assembly LIB006R05 Edition: 05-2005 Chapter 6 ENGLISH Child's bicycle seat OKBABY SIRIUS Page 68 Chapter 6 Child's bicycle seat OKBABY SIRIUS Page 69 ENGLISH Illustration 3: Insert the support arm (5) pushing it until the correct position 25. IIllustration 6: Choose the plastic adapter (10) suitable to the diameter of the frame of your bicycle and fix the fixing block (8) and the relative fixing counter-block (7) to the bicycle. Leave the screws (9) slightly loose in order to adjust the height of the seat. 9 10 8 7 25 Illustration 7: Take the seat and fit the ends of the support bar (5) in the two holes on the support block. Make sure that the safety lever 17 is locked into the housings of the support arm. If the lever snaps into place, you can no longer extract the support bar from the frame fastening block, unless you operate the lever. Position the seat back vertically by turning the knob (16) (see illustration 2) anticlockwise. At this stage, check that: The centre of gravity reference point 18 on the seat is not more than 5 mm away from the centre of the wheel. Rotate the inclination knob (16) until the desired position of the backrest. Changing the inclination of the backrest, the seat moves forward and the footrests could interfere with pedalling. 120° Illustration 10: Fixing the footrests. To fix the footrest, insert it into the highest position in the shaped adjustment housing, keeping the fixing bridges of the belts outside the child's seat. Insert the regulating pin 21 from the outside of the seat towards the inside, as shown, making sure that the right pin meets the right side and vice versa. [. . . ] Repairs must be carried out only by authorized and specialized personnel. Address for assistance: Telephone: +39 (035) 830004 Fax: +39 (035) 832961 E-mail for technical information: aq. baldelli@okbaby. it 10 List of problems Possible cause/s Remedy · Replace the screws and nuts. · Only use screws that correspond to the original screws and/or get information from the manufacturer/dealer. · Do not mount the child's bicycle seat on the corresponding bicycle. Problem The blocking screws cannot be tightened and/or have been tightened excessively during assembly. [. . . ]