User manual NUMARK TT200

[. . . ] Water and Moisture This product should be kept away from direct contact with liquids. Heat - Avoid placing this product to close to any high heat sources such as radiators. Ventilation - The appliance should be situated so that it's location or position does not interfere with it's proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation opening; or, placed in a builtinstallation, such as bookcase or cabinet that may impede the flow of air through the ventilation openings. [. . . ] Channel Input Selector ­ determines what input source is controlled by the channel. MICROPHONE Mic Gain Controls ­ Controls the volume of the microphones Mic Activation Switch ­ turns microphone input on and off. Treble and Bass Controls ­ for fine-tuning the tone of your voice on both mics through the sound system. This works with the auto talk-over sensitivity adjustment on the rear panel. Talkover is very useful for making announcements without adjusting any levels. 9. 10. 11. 5. 14. 15. 8. HEADPHONE CUEING Channel Cue Assign - are used to route Pre Fader Level (PFL) channel audio to the Monitor Section. Split/Blend Cue ­ controls how PFL and Program audio are sent to your headphones. In split mode, the PFL audio can be heard in your left ear and PGM audio can be heard in your right ear. Headphone Mix - controls the mix of PFL and PGM signals to your headphones. When the slider is moved to the left, all you will hear is the cue source. When the slider is all the way to the right, you will hear what is playing through the master output. Then remove the 2 fader screws that hold the crossfader to the subchassis, lift it out and disconnect its cable. Re-attach the new crossfader and replace the faceplate and knobs back onto the unit - you're back in business!Crossfader Slope ­ determines how quickly the audio from the opposing side of the crossfader activates. A tight curve (hard right) turns on the opposing audio signal with very little crossfader movement. A loose curve (hard left) makes very long and smooth segues in transition. Crossfader Assign Knob - determines which input channel will be heard when the crossfader is moved towards the knob and which channel is fader start. Fader Start ­ activates the crossfader to send play and cue commands to your auto-start Numark CD player or other popular brand using pulse technology. For fader start, attach your mixer to a remote start CD player using industry standard 1/8"(3. 5mm) cables. When you move the crossfader toward the active channel, the attached CD player will start. When it is moved away, that side will cue (similar to pressing the cue button). Power Indication LED ­ indicates when power is applied to the unit and the rear panel power switch is on. - The Leader in DJ Technology ©2000 Industries -9http://www. numark. com TT200/TT200R REAR PANEL FEATURES 26 25 24 17 15 10 8 7 3 2 1 1. [. . . ] maximum output): Line: Better than 96 dB Mic: Better than 78 dB Phono: Better than 87 dB *JIS - weighted FREQUENCY RESPONSE: Line: 20 Hz- 22k Hz ±0. 5 dB Line: 20 Hz- 20k Hz ±0. 5 dB Phono: ±1 dB except for controlled attenuation of -3 dB @ 20 Hz to reduce rumble and feedback EQUALIZER: Bass: Low Middle: Middle: Treble: +/-6, 12dB @ +/-6, 12dB @ +/-6, 12dB @ +/-6, 12dB @ POWER CONSUMPTION: 21. 6 Watt typical 28. 8 Watt with full headphone output DIMENSIONS: WEIGHT: kgs, lbs - The Leader in DJ Technology ©2000 Industries - 13 http://www. numark. com Professional Disc Jockey Products LIMITED PRODUCT WARRANTY What is covered and for how long?NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK products; including but not limited to DJ mixers, amplifiers, CD players, CD Mix Stations, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, cartridges, and all other accessories; are to be free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer for a period of (1) Year. This Limited Warranty is conditioned upon proper use of the product by the purchaser. This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification of any part of the product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally exposed parts that are scratched or damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment, or service of the mixers; (e) crossfaders. [. . . ]