User manual NUMARK TT1650

[. . . ] TT-1650 Operating Instructions INSIDE THE BOX: (1) TT-1650 Turntable (1) Aluminum Platter (1) Headshell w/ Cartrdige (1) Counter Weight (1) IEC Power Cable (1) Slipmat (1) RCA Cord w/ Ground Wire Thank you for buying this Numark product. Please read these operating instructions so you will know how to operate this equipment properly. After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] Carrying Handles These handles provide a secure grip so that the turntable may be comfortably transported. RCA Output Jacks These stereo output jacks allow the turntable to be connected to a compatible device with a PHONO level input. Ground Screw This Ground Screw is used to run a ground line between the turntable and the device it is connected to. Voltage Selector Switch This two-position switch toggles the internal voltage transformer between 110V and 240V. The turntable should be shipped with the proper voltage setting for your region. Check this switch setting before connecting the IEC power cord to prevent damage to the turntable. IEC Power Terminal This IEC Power Terminal can be used with any IEC power cable, but it is recommended that the supplied IEC power cable be used. 12 x4 13 x4 17 16 14 15 CONTROLS PAGE 4 SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a variety of different ways depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions. If a mixer is placed between two turntables make sure that there is at least ¼" (7mm) between the mixer and the turntables to prevent damage to the turntables and to reduce unwanted system noise. Mixer Mixer 85 mm ¼" ¼" Setup Style 1 (traditional) Best For: Long mixes and blending techniques Mixer ¼" ¼" Setup Style 2 (battle style, scratching) Best For: Scratching, cutting and aggressive mixing techniques Mixer There are many variations of these setups. Find the best setup that works for your mixing style by experimenting with different turntable and mixer placements. It is strongly recommended that the top mixer surface and the top flat surface of the turntable be at the same level. PAGE 5 SETUP & INSTALLATION PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability or permanent motor damage. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them. This turntable will not work properly if connected to a LINE LEVEL input or CD input. 1. 2. 3. 4. 5. 6. REAR or SIDE PAGE 7 CABLE SETUP TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: Balancing the Tone Arm 1. Begin the balancing process by lifting the cue lever to the up position (or make sure that the stylus protector is on the cartridge. ) 2. Next, rotate the counterweight clockwise until it is in the complete forward position (NOTE: this is also the maximum amount of pressure that can be applied to the cartridge. ) 3. Now there should be a feeling of weight and resistance when the head shell is raised and lowered. Begin rotating the counterweight counter-clockwise (away from the pivot point) until this weight and resistance feeling is gone. If done properly, the tone arm will pivot with very little resistance back and forth indicating that there is exactly 0 grams of stylus pressure. With the counterweight in its new position further away from tone arm pivot point, grasp the scale ring of the counter weight and rotate it until "0" is in the vertical position. Finally, rotate the counterweight (and scale ring) clockwise (towards the pivot point) until the desired amount of weight is reached. If the scale rotates 360 degrees beyond the zero point, the new scale ring reading should be added to 3. 5. [. . . ] EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK PRODUCT, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S PRODUCTS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS. [. . . ]