User manual NUMARK PRO TT-1

[. . . ] Internal/External Voltage Selectors Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. NOTE: This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to moisture. Electrical equipment should NEVER be kept or stored in damp environments. CAUTION FOR USA & CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. SAFETY INSTRUCTIONS 1. [. . . ] Place the supplied slipmat on the Center Spindle now. - The Leader in DJ Technology ©1999 Industries 6 http://www. numark. com PRO TT-1 8. 45 Adapter - Place on Center Spindle (7) for playing 7" records with large center holes. Forward/Reverse Buttons - These determine the direction the platter will spin. Lid Hinge Holder - Place the bottom tabs of your lid hinges in here after you finish assembly. Pitch Adjust - use this the change the speed of the platter when quartz lock is inactive. Voltage Selector - with unit unplugged set the desired voltage for your location using a screw driver. 115V 14. Quartz Lock On - will hold the revolution speed at exactly the specified speed (3) Off - will allow use of the Pitch Adjust (13) 15. Target Light - Press the button to the right and a light will pop up directed at the stylus position. 230V TONE ARM ASSEMBLY 30 29 28 20. When installing a cartridge, refer to the installation instructions supplied by the manufacturer of that cartridge. During installation, attach the stylus protector to guard the stylus tip from damage. Attach wires as follows: White (L+)Left channel+ Blue (L-)Left channel Red (R+)Right channel+ Green (R-)Right channel 27 25 24 23 21. Headshell Locking Nut - Attach headshell by inserting into the front end of the tonearm, then turn the locking nut clockwise with the head shell firmly held horizontally. 26 22 22. Tone Arm Clamp and Rest - Use this rest the tone arm and clamp it in position during transportation. 21 20 24. Tone Arm Lift - This elevates the tone arm above the record surface 25. Tone Arm Lever - Controls the up and down action of the Tone Arm Lift - The Leader in DJ Technology ©1999 Industries 7 http://www. numark. com PRO TT-1 27. Anti-Skate Control - This applies inward force to the tonearm so it doesn't skip outward across the record due to the centrifugal force of the record spinning. Tone Arm Height Adjust - This allows the tone arm to be properly align with the platter surface. Platter Speed Output - This output is to be used with external devices the require platter speed information. Tech note: This circuit is a normally open, use a momentary switch and a 1/4" mono plug to change play states of the unit. 44. Phono Output - Plug these into your mixer or preamplifiers' turntable input. Ground Cable - Attach to the ground screw on your mixer or preamplifier to prevent turntable hum. Power Cord - Plug this into an appropriate power outlet after checking your power setting switch (18) under the platter. [. . . ] SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER. You may also have other rights, which vary from one jurisdiction to another. RETURN INFORMATION 1. A Return Authorization number must be obtained from Numark through the address or phone numbers below. A copy of the original sales receipt must also be included for the equipment to be repaired under warranty. [. . . ]