User manual NUMARK MATRIX3

[. . . ] Matrix 3 Operating Instructions Thank you for buying this Numark product. Please read these operating instructions so you will know how to operate this equipment properly. After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] Turning the knob completely to the right increases the level to +10dB and turning the knob completely to the left decreases the level. Blue Power LED The blue power LED will illuminate when the mixer has been connected to a power source and switched to the "on" position (See Section 9 "Inputs and Outputs. ") 6. Crossfader Controls Crossfader with Tracking Light System This slide fader blends between the assigned inputs set by the "Assign" switches on the front Panel. Its action can be fine-tuned using the "Slope" control or it can be reversed or deactivated by the "Direction" switch. A red light glows on either the right, left or both sides for the Crossfader indicating only the position of the Crossfader, not the amount of signal being sent to the master output. "Slope" (Crossfader Curve Style Control) The position of this knob determines where the startup level of the assigned channel (see "Assign" switches) will lie on the Crossfader. When turned to the left, the Crossfader will gradually fade the assigned channel in to the master output signal as it is engaged. When it is turned all the way to the right, a very sharp fade of the assigned channel will occur immediately when the fader is engaged. "Assign" (1/2 switch and 2/3 switch) The position of these switches determines which input channel is assigned to the Crossfader. The left switch assigns either Channel 1 (left switch setting) or Channel 2 (right switch setting) to the left side of the Crossfader. The right switch assigns either Channel 2 (left switch setting) or Channel 3 (right switch setting) to the right side of the Crossfader. "Direction" (Crossfader Reverse and Deactivation Control) The position of this switch can reverse or deactivate the assigned channels of the Crossfader. In the left switch setting, the channels are assigned according to the "assign" switches. In the right switch setting, the channels are reversed from their settings of the "assign" switches. In the center position, the Crossfader is deactivated. PAGE 11 MASTER OUTPUT, CROSSFADER CONTROLS SECTION 5 SECTION 6 MASTER OUTPUT, CROSSFADER CONTROLS PAGE 12 CONTROLS 7. Special Crossfader Related Features "Kill" (Flash/Eliminate EQ Toggles) These toggles eliminate the signal level for their respective frequency (low range, midrange and high. ) In the upward position, the switch will lock in position. In the downward position, the switch eliminates the frequency until it is released. The left set of kill switches is used to control the sound of the input assigned to the left side of the Crossfader. The right set of kill switches is used to control the sound of the input assigned to the right side of the Crossfader. Punch In/Out Transform Buttons The punch buttons are used to instantly switch or eliminate the output of the mixer depending on the Crossfader position. See "Punch" In/Out Switches for details on the settings and action of this control. "Punch" (Punch In/Out switches) The position of these switches determines whether the output sound will be eliminated or replaced with the output assigned to the opposite channel. [. . . ] During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the purchaser, any defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return authorization number ("RA#"). Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales receipt or comparable proof of sale showing the date of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and assistance on where to return the mixer, contact NUMARK customer service at 401-295 9000. [. . . ]