User manual NUMARK MATRIX2

[. . . ] Matrix 2 Operating Instructions Thank you for buying this Numark product. Please read these operating instructions so you will know how to operate this equipment properly. After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] "Treble" (Input Level High EQ) This rotary control adjusts the high-tone sound of the inputs. Turning the knob completely to the right increases the level (to +10dB at 15kHz. ) Turning the knob completely to the left decreases the level (to 28dB at 15kHz. ) "Middle" (Input Level Midrange EQ) This rotary control adjusts the mid-tone sound of the inputs. Turning the knob completely to the right increases the level (to +12dB at 1kHz. ) Turning the knob completely to the left decreases the level (to 32dB at 1kHz. ) "Bass" (Input Level Low EQ) This rotary control adjusts the low-tone sound of the inputs. Turning the knob completely to the right increases the level (to +12dB at 40Hz. ) Turning the knob completely to the left decreases the level (to 32dB at 40Hz. ) "PFL" (Input Level Meter and Cue Button) These meters display the peak levels of the inputs. You can use the "Gain" and EQ controls to match the levels of input signals while Cueing. The Volume should always be set at its lowest setting while connecting and disconnecting headphones to prevent damage to headphones and/or your hearing. "PFL" (CH-1, CH-2, CH-3 and Mic PFL Buttons) CH-1, CH-2, CH-3 and the Microphone can be sent to the headphones one at a time or simultaneously for cueing. When depressed, the PFL (cue) button illuminates yellow indicating that the source is being cued. Use the "Mix" control to get a balance of the cued PFL source(s) and the master output in the headphones. PAGE 9 METERS+ LIGHTING, CUEING CONTROLS SECTION 3 SECTION 4 METERS+ LIGHTING, CUEING CONTROLS PAGE 10 CONTROLS 5. Master Output Controls "Master" (Main Output Level Control) This rotary control adjusts the main output levels for any equipment connected to the Master Output on the rear panel (Section 9 "Inputs and Outputs". ) Turning the knob completely to the right increases the level to +10dB and turning the knob completely to the left mutes the signal. "Booth" (Master/Split Style Headphone Cueing Switch) This rotary control adjusts the auxiliary (AKA booth) output levels for any equipment connected to the Booth Output on the rear panel (Section 9 "Inputs and Outputs". ) Turning the knob completely to the right increases the level and turning the knob completely to the left mutes the signal. Blue Power LED The blue power LED will illuminate when the mixer has been connected to a power source and switched to the "on" position (See Section 9 "Inputs and Outputs. ") 6. Crossfader Controls Crossfader with Tracking Light System This slide fader blends between CH-1 and CH-2. Its action can be fine-tuned using the "Slope" control switch or it can be reversed or deactivated by the "Direction" switch. A red light glows on either the right, left or both sides for the Crossfader indicating only the position of the Crossfader, not the amount of signal being sent to the master output. "Slope" (Crossfader Curve Style Control) The position of this switch determines where the startup level of CH-1 and CH-2 lie on the crossfader (with respect to "Direction. ") When switched to the left, the Crossfader will gradually fade the channel in to the master output signal as it is engaged. When switched to the right, a very sharp fade of the channel will occur immediately when the fader is engaged. "Direction" (Crossfader Assignment Reverse and Deactivation Control) The position of this switch can reverse the assignment of CH-1 and CH-2 or deactivate the Crossfader. In the left switch setting ("Normal", ) CH-1 is assigned to the left side of the Crossfader and CH-2 is assigned to the right side of the crossfader. In the right switch setting, the assignment of CH-1 and CH-2 are reversed on the Crossfader. In the center position, the Crossfader is deactivated. PAGE 11 MASTER OUTPUT, CROSSFADER CONTROLS SECTION 5 SECTION 6 MASTER OUTPUT, CROSSFADER CONTROLS PAGE 12 CONTROLS 7. Special Crossfader Related Features "Fader Start" (Fader Start On/Off switches) When engaged the fader start can be used to instantly start a fader-start compatible device (See "Inputs and Outputs" Section 9) by moving the Crossfader away from the endpoints. [. . . ] THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS. This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications to this Limited Warranty, or make additional warranties binding on NUMARK. [. . . ]