User manual NUMARK DM950

[. . . ] FOLLOW INSTRUCTIONS All operating and use instructions should be followed. The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzene, insecticides or other volatile liquids since they may corrode the cabinet. ATTACHMENTS Do not use attachments not recommended by the product manufacturer as they may cause hazards. [. . . ] Connect the AC plug into the jack on the rear of the mixer (A. ) The mixer should be switched on after all devices are already connected to prevent damage to your equipment. Master Volume This rotary control adjusts the main output levels for any equipment connected to the Master Output on the rear panel (B. ) Turning the knob completely to the right increases the level and turning the knob completely to the left decreases the level. 3. CH 1 Trim, Treble and Bass "Trim" (Input Level Trim) (4. applies to CH 2) This rotary control adjusts the input signal levels of the inputs. Turning the knob completely to the right (clockwise) increases the level. Turning the knob completely to the left (counter clockwise) decreases the level. "Treble" (Input Level High EQ) This rotary control adjusts the high-tone sound of the inputs. "Bass" (Input Level Low EQ) This rotary control adjusts the low-tone sound of the inputs. Microphone Trim One microphone can be connected to the Quarter Inch output terminal (G). The Microphone Trim should always be at its lowest setting while connecting and disconnecting a microphone to prevent damage to the mixer and/or your audience. 6. CH 1 Input Selector Switch This two position Toggle Switch engages the Phone Input in the upward position (F) or the Line Level Input in the downward position (E. ) 7. CH 2 Input Selector Switch This two position Toggle Switch engages the Phone Input in the upward position (D) or the Line Level Input in the downward position (C. ) 8. CH 1 Input Fader This slide fader continually adjusts the level of the selected CH 1 input sources (See Control 6. ) In the full upward position, the level is set to the maximum output. 9. CH 2 Input Fader This slide fader continually adjusts the level of the selected CH 2 input sources (See Control 7. ) In the full upward position, the level is set to the maximum output. 10. CH 1 and CH 2 Crossfader This slide fader blends between the assigned inputs set by the Input Selector Switches (6 and 7). In the full left position, only CH 1 is sent to the Master Output (B. ) In the full right position, only CH 2 is sent to the Master Output. In the center position, a mix of the levels of CH 1 and CH 2 are combined and sent to the output. 11. Mini Slide Fader Cueing System This mini slide fader can be used as a "Crossfader" for previewing mixes in the connected headphones (H. ) The level of the headphones is adjusted using the Cue Trim knob. NOTE: Be sure that the level of the cue trim is always set to a minimum before connecting or disconnecting headphones. PAGE 3 MIXER CONTROLS 2 1 3 4 5 6 7 8 9 11 10 G H A B C D E F MIXER CONTROLS PAGE 4 MIXER CONTROLS Input and Power Section continued NOTE: It is recommended that the mixer be turned off before connecting or disconnecting anything to/from the mixer. A. Power Switch and AC Jack Use only the included AC Power Adapter when operating this mixer. RCA Master Output This RCA output is for connecting an external monitoring device such as a PA system, powered monitors or a home stereo. The level of the master stereo output signal increases as the Master Volume (2) control is increased. C. [. . . ] g) The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and original sales receipt enclosed to: NUMARK INDUSTRIES Attention: Service Department 11 Helmsman Avenue North Kingstown, RI 02852 USA Phone: 1 (401) 295-9000 Fax: 1 (401) 295-5200 Web: www. numark. com PAGE 9 RETURN INFORMATION Problem Mixer does not turn on. The Turntable is not connected to a device with a PHONO preamp. Solution Connect Power Cord. Connect the turntable to the input labeled PHONO, not the LINE. The sound is on one side only. The RCA audio cord is disconnected. The RCA audio cord is damaged. Properly secure the RCA cable to the mixer. [. . . ]