User manual NUMARK DM2000X

[. . . ] Internal/External Voltage Selectors Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. NOTE: This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments. CAUTION FOR USA & CANADIAN MODELS ONLY TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. SAFETY INSTRUCTIONS 1. [. . . ] "Clipping" is when the power amplifier is distorting and working beyond it's limits. · To prevent fire or shock hazard, do not expose the unit to rain or moisture. Never place cans of beer, soda, glasses of water or anything wet on top of the mixer! A NOTE ON CABLES: Make the input and output connections with readily available low-capacitance stereo cables. See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get. Numark - The Proven Leader in DJ Technology ©1997 Numark Industries 5 http://www. numark. com DM2000X DM2000X FRONT PANEL DIAGRAM. . . GUIDED TOUR OF FEATURES AND OPERATING INSTRUCTIONS. . . If the D M 2 0 0 0 X is your first mixer, please read this entire manual before you begin operation. The D M 2 0 0 0 X can be 10" rack-mounted or used as a free-standing unit. Keep in mind that there are a few features you may never have seen before in a mixer of this type that you will need to read about. Finally, connect the stereo outputs to the power amplifier(s) and/or audio sources. Now you are ready to switch it on. 13 6 16 17 5 3 1 2 4 14 12 11 10 7 15 14 9 8 CHANNEL FEATURES 1. Channels 1, 2, & 3 Rotatable Input Toggle Switches select which source will be live to that channel based on what you have connected to the rear panel input section. To rotate lift of toggle and place in it's new position or to replace unplug the old unit and plug in the new one. The Input Faders are low-noise, low-impedance, high-quality, smooth AlpsTM faders. The P F L pushbuttons are used to route channel audio to the main volume meter and the Cue Monitor Section. When a PFL is pressed the main volume meter changes its display to the PFL channel. This allows the DJ to accurately match levels before mixing with that channel's gain control. The idea is to properly match inputs, not the input with the output! 4. Send Buttons are for allowing a channels pre-fader output to be sent to the send connectors in the rear of the unit. Treble, Mid, and Bass Controls are for setting appropriate equalized levels for the music you are playing. When turn all the way left they "CUT" the signal by 30dB for special effects mixing. Gain Controls are for accurately matching audio levels of the channels. Numark - The Proven Leader in DJ Technology ©1997 Numark Industries 6 http://www. numark. com DM2000X CROSSFADER SECTION 7. The Replaceable Crossfader achieves clean segues between the two selected input channels. Use the crossfader for fast and seamless segues from one selected channel to the other. Simply unscrew the two large screws which hold it in place, lift it out and disconnect it's cable. [. . . ] This warranty does not extend to any of our products which have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, or use in violation of instructions furnished by us, nor extended to units which have been repaired or altered outside of our factory, nor to cases where the serial number thereof has been removed, defaced, or changed, nor to accessories used therewith not of our own manufacture. Numark reserves the right to make changes or improvements in its products, during subsequent production, without incurring the obligation to install such changes or improvements on previously manufactured equipment. To place this warranty into effect, the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries, LLC within thirty (30) days after date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. [. . . ]