User manual NUMARK DM1125

[. . . ] Professional Disc Jockey Products DM1125 STEREO MIXER with Digital Sampler OWNER'S MANUAL NUMARK INDUSTRIES 11 Helmsman Road, North Kingstown RI 02852 http://www. numark. com DM1125 Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 2 http://www. numark. com DM1125 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE ANY COVER. The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this appliance. 6. Heat - Avoid placing this product too close to any high heat sources such as radiators. [. . . ] Use the crossfader for fast and seamless segues from one selected channel to the other. To turn off the crossfader simply turn both knobs all the way to the left. Simply unscrew the two large screws which hold it in place, lift it out and disconnect it's cable. Re-attach the new crossfader and screw the mounting plate back onto the unit - you're back in business!The Crossfader Assign knob to the right of the crossfader lets you choose which input channel will be heard when the crossfader is in the far right position. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 8 http://www. numark. com DM1125 DJ MIC SECTION The D M 1 1 2 5 has an extremely flexible DJ Mic channel. The Talkover function reduces the level of the music while leaving the DJ Mic at normal volume. NeutrikTM "Combo" connector allows connection of either a 1/4" jack or an XLR jack for the DJ Mic 1. This is ideal for connecting an XLR gooseneck directly into the mixer. Treble and Bass Controls fine tune the tone of your voice on both mics through the sound system. The DJ Mic 1 Fader controls the DJ Mic volume for the NeutrikTM "Combo" connector. The Mic 2 Fader controls the Mic volume for the 1/4" connector on the rear of the mixer. O f f turns off Mic 1 O n turns on Mic 1 Talkover turns down the input level of your music sources from Channels 1-4. Talkover is very useful for making announcements without adjusting any levels. Try using this feature for audience participation when you want the music to temporarily cease and the audience to be heard - "YEAH!" MASTER/BOOTH OUTPUT SECTION 12. Stereo/Mono toggle adjusts the Master output for the operation selected. The Booth Level controls speaker volume for a remote zone or booth monitors. If you do not use booth monitors the output can feed a tape deck, another amplifier, another mixer or a satellite speaker system. Note: This can also be used to supply line level audio to a lighting controller or to lights that are sound activated. CONTRACTOR'S NOTE: Booth Level provides zone control in installations where there are two separate rooms, or a bar and dance floor, for example. The red LEDs for +3dB, +5dB and +8dB hold program peaks for a second or two. With peak metering, it's OK to be "in the red" as long as +5dB or +8dB aren't constantly lit. Set the crossover, equalizer and power amp inputs to avoid distortion at each step in the audio chain. [. . . ] d- Hit Start-Stop a second time to stop the sampling, or allow the memory banks to fill up, at which time sampling will stop automatically. The sampler is now ready for playback. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 11 http://www. numark. com DM1125 DM1125 REAR PANEL DIAGRAM. . . 1 6 2 4 5 3 7 7 78 7 8 REAR PANEL: INPUTS AND OUTPUTS 1. See safety precautions on page 3 for proper treatment of the power cord. GND is the grounding lug for turntables 1 and 2 (phono inputs on Channels 1 and 2). [. . . ]