User manual NUMARK DJ18

[. . . ] Grounding or Polarization - Precautions should be taken so that the grounding or polarization means built into the mixer is not defeated. Internal/External Voltage Selectors - Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. NOTE: This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. [. . . ] Never place cans of beer, soda, glasses of water or anything wet on top of the mixer! A NOTE ON CABLES: Make the input and output connections with readily available low-capacitance stereo cables. See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 7 http://www. numark. com DJ18 DJ18 FRONT PANEL DIAGRAM. . . 7 1 2 13 12 16 19 11 15 20 9 10 3 8 17 5 4 6 14 18 GUIDED TOUR OF FEATURES AND OPERATING INSTRUCTIONS. . . Please read this entire manual before you begin operation. Finally, connect the stereo outputs to the power amplifier(s) and/or audio sources. The DJ18 is divided into five functional blocks: Input, Crossfader, DJ Mic, Master/Zone Output, and Equalizer. Channels 1, 2, & 3 Input Toggle Switches select which source will be live to that channel based on what you have connected to the rear panel input section. The Input Faders are low-noise, low-impedance, highquality, smooth AlpsTM faders. The C u e pushbuttons are used to route channel audio to the Monitor Section. The channel faders do not control the C u e send volume. CROSSFADER SECTION 4. The Crossfader Assign knob to the left of the crossfader lets you choose which input channel will be heard when the crossfader is in the far left position. 5. The Replaceable Crossfader achieves clean segues between the two selected input channels. Off1 2 3 Off1 2 3 "Hard left" selects the channel set up of the Assign Left knob. "Hard right" selects the channel set up on the Assign Right knob. Use the crossfader for fast and seamless segues from one selected channel to the other. To turn off the crossfader simply turn both knobs all the way to the left. Simply unscrew the two large screws which hold it in place, lift it out and disconnect it's cable. Re-attach the new crossfader and screw the mounting plate back onto the unit - you're back in business!The Crossfader Assign knob to the right of the crossfader lets you choose which input channel will be heard when the crossfader is in the far right position. Numark - The Proven Leader in DJ Technology ©1998 Numark Industries 8 http://www. numark. com DJ18 DJ MIC SECTION The D J 1 8 has an extremely flexible DJ Mic channel. The Talkover function reduces the level of the music while leaving the DJ Mic at normal volume. NeutrikTM "Combo" connector allows connection of either a 1/4" jack or an XLR jack for the DJ Mic 1. This is ideal for connecting an XLR gooseneck directly into the mixer. Treble and Bass Controls fine tune the tone of your voice on both mics through the sound system. The DJ Mic 1 Fader controls the DJ Mic volume for the NeutrikTM "Combo" connector. The Mic 2 Fader controls the Mic volume for the 1/4" connector on the rear of the mixer. [. . . ] Numark shall not be liable for any damages, consequential or otherwise, resulting from the use and operation of this product and makes no other warranty(s) either express or implied on this product, including any warranty of merchantability. This warranty does not extend to any of our products which have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, or use in violation of instructions furnished by us, nor extended to units which have been repaired or altered outside of our factory, nor to cases where the serial number thereof has been removed, defaced, or changed, nor to accessories used therewith not of our own manufacture. Numark reserves the right to make changes or improvements in its products, during subsequent production, without incurring the obligation to install such changes or improvements on previously manufactured equipment. To place this warranty into effect, the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries, LLC within thirty (30) days after date of purchase. [. . . ]