User manual NOVAK PRO SC SET-UP GUIDE

[. . . ] 6. 0 volts DC / 3 amps Power Wire (Battery/Motor). . . . . . . . . . . . . . . . . . . . . . . . . Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PUSH TRANSMITTER THROTTLE TO FULL-BRAKE/REVERSE Hold it there until the green status LED blinks green. Note: Motor will not run during programming even if connected. With transmitter throttle at neutral, and still pressing the SET button, slide the ESC's ON/OFF switch to ON position. 8. [. . . ] DISCONNECT BATTERIES WHEN NOT IN USE 2S LiPo/LiFe OR 4-6 NiMH CELLS ONLY BRUSHLESS MOTOR CONNECTOR WIRE SET [Novak kit #5332] BRUSHLESS SENSOR HARNESSES [Novak kit #5351-#5353] LOW-PROFILE HEAT SINK [Novak kit #S5431] Flexible 14GA wire with gold-plated connectors for low-resistance connections. Shielded sensor harness protects sensor wires and provides multiple installation options. 4"/100mm (Novak #5351), 6"/150mm (Novak #5352), & 9"/230mm (Novak #5353). Wiring and cooling fan This section shows the polarity of the Havoc Pro SC's output pins. The included receiver harness (Novak #5309) has a 2mm mini plug on the end that is plugged into the ESC and a standard JST plug on the receiver end. The included ON/OFF switch (Novak #5602) has a standard JST plug on it. Before connecting, note the wiring sequence of the installed harness connectors as shown here. The Havoc Pro SC's heat sink is designed to accept a 25x25mm cooling fan, and comes with nylon 4-40x5/8" screws to secure it. To install, simply center the fan on the ESC and push the nylon screws down into the cross cuts of the heat sink. Install the fan's power connector onto the fan output pins on the ESC--note polarity as shown below. Novak #5649 installed product warranty The Havoc Pro SC Brushless ESC is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). Includes thermal gap pad. SUPER-FLEX SILICONE 14GA WIRE SET [Novak kit #5508] SUPER-FLEX SILICONE 12GA WIRE SET [Novak kit #5512] Two each of 9" length black, red, blue, yellow, and orange 14GA wire. Optional wire set is perfect for low-resistance connections. NO REVERSE VOLTAGE! POWER TRANS-CAP MODULE REQUIRED REMOTE POWER PROGRAMMING SWITCH [Novak kit #5602] 25x25x10mm COOLING FANS [Novak kits #5649 & #5653] POWER TRANS-CAP MODULE [Novak kit #5679] Includes ON/OFF Power Switch and One-Touch Programming Button harness. Cooling fans fit heat sink perfectly & has the Havoc Pro SC's 2mm Mini power plug for easy connection. Replacement Power Trans-Cap Module provides improved efficiency and lowers operating temperatures. It is compatible with 2S LiPo and 4-6 cell NiMH. TRANSMITTER ON FIRST GOOD QUALITY LiPo/LiFe BATTERIES SUGGESTED Sensor harness Receiver harness ON/OFF switch black wire (negative) (positive) POWER CONNECTORS­3. 5mm & 4mm [Novak kit #5731 & #5741] LEAD-FREE SILVER SOLDER [Novak kit #5831-#5833] Low-Loss connectors generate dozens of wiring routing and installation options. Novak solder contains 3% Silver for high-conductivity and is available in three sizes. 6g in Novak kit #5831, 15g in Novak kit #5832, and 100g in Novak kit #5833. GOOD QUALITY RADIO SYSTEM SUGGESTED positive fan pin negative fan pin red wire white wire (signal) MOUNTING TAPE 25x35mm [Novak kit #5840 & #5841] HEAT SHRINK TUBING [Novak kit #5850 & #5851] FIGURE 4 FIGURE 5 Fan power output pins 2mm Mini black wire plug (negative) standard JST plug Includes cushioned, double-sided tape to secure electronics in vehicles. Novak heat shrink tubing is 6" long and available in six sizes: 1/16" - 3/8". 6 piece assortment in Novak kit #5850, and 24 piece assortment in Novak kit #5851. DO NOT BUNDLE POWER & SIGNAL WIRES TOGETHER RF noise in the power wires can adversely effect radio system performance. Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short circuits, which can damage the ESC. Exposure to CA glue or its fumes can cause damage to internal components of the ESC and result in premature failure. INSULATE WIRES NO CA GLUE www. teamnovak. com TRAXXAS® SLASHTM 4X4 ESC MOUNTING PLATE [Novak kit #5090) Mounting plate and hardware to install ESC into Traxxas® SlashTM 4x4. P4 P1 step 1­connect input harness HAVOC PRO SC 550-SIZED SET-UP PHOTO The Havoc Pro SC has a userreplaceable input harness with a 2mm mini plug on the ESC end of it and the industry-standard connector on the receiver end of it. The Havoc Pro SC works with all major radio brand's new receivers [Refer to Figure 1 to see how to connect the included user-replaceable input harness]. However, some very old receivers must have the wiring sequence in the plastic 3-pin JST connector housing changed on the receiver end. Servo plugged into steering ch. [. . . ] Red power wire (battery positive) FACTORY-INSTALLED POWER TRANS-CAP MODULE REQUIRED Userreplaceable input signal harness (Ch. 2) Set button (Novak #5679) DO NOT USE SCHOTTKY DIODES MOTOR CAPACITORS NOT NEEDED (FIGURE 3) Novak sensor-based, 540-sized brushless motor Sensor harness Blue motor phase wire (Phase A) step 4­Wire ESC to Battery To connect the Havoc Pro SC to the main battery pack using connectors, we suggest low-loss high power connectors like Dean's Ultra Plug. · Use a female connector on battery packs to avoid shorting. Good Quality Radio System Suggested With the higher performance of brushless systems, undesirable radio system noise may occur when used with lower quality radio systems. FM radio systems are acceptable, as long as the system is high quality. AM radio systems are not recommended. Black power wire (battery negative) 2. 4 GHz FM AM Orange motor phase wire (Phase C) Yellow motor phase wire (Phase B) Battery connector 1. [. . . ]