User manual NOVAK FUSION ESC

[. . . ] · 6 OR 7 CELLS ONLY Never use more than 7 or fewer than 6 cells (1. 2 volt DC/cell) in the main battery pack. · MOTOR CAPACITORS REQUIRED Three 0. 1µF (50V) ceramic capacitors must be properly installed on every motor to prevent radio interference. · DON'T LET TRANSISTOR TABS TOUCH Never allow the two transistor tab banks or the heat sinks to touch each other or any exposed metal, as this will create a short circuit and damage the speed control. · DISCONNECT THE BATTERIES Always disconnect the battery pack from the speed control when not in use. [. . . ] Set HIGH ATV or EPA to maximum setting. [Controls amount of throw from neutral to full throttle] TROUBLE-SHOOTING GUIDE This section describes possible speed control problems, causes, and solutions. Steering Channel Works But Motor Will Not Run · Speed control has thermally shut down­­Allow ESC to cool down­­Use milder motor or smaller pinion gear. · Make sure ESC is plugged into the throttle channel of receiver. · Possible internal damage­­Refer to Service Procedures. 1. INSTALL MOTOR CAPACITORS Electric motors generate radio noise that can interfere with your receiver and cause radio problems. Included in the accessory kit with the speed control are three 0. 1µF (50V) non-polarized, ceramic capacitors. These capacitors must be installed on every motor to help reduce the noise generated by the motor and also to prevent possible damage to the speed control. Solder 0. 1µF (50V) capacitors between: · POSITIVE (+) motor tab & NEGATIVE (-) motor tab. · NEGATIVE (-) motor tab & GROUND tab*. *If your motor does not have a ground tab, solder the capacitor leads to the can of the motor as shown below. 2. Set LOW ATV, EPA, or ATL to maximum setting. [Controls amount of throw from neutral to full brakes] [Reduce this after ESC adjustment to reduce amount of brakes] 3. Set EXPONENTIAL to zero setting. [Controls the linearity of the throttle channel] Receiver Glitches/Throttle Stutters During Acceleration · Motor capacitors broken or missing­­Refer to Step 4. · Receiver or antenna too close to speed control, power wires, battery, or motor­­Refer to Step 3. · Excessive current to motor­­Use a milder motor or a smaller pinion gear. 4. Set THROTTLE CHANNEL TRIM to middle setting. [Adjusts the neutral position of speed control] [Increase or decrease after ESC adjustment to adjust coast brakes­­can be used to give braking in neutral trigger position] Negative (-) motor tab 0. 1µF Capacitors Schottky diode Positive (+) motor tab Extra 0. 1µF capacitors available in Novak kit #5620. Set THROTTLE CHANNEL REVERSING SWITCH to either position. [Do not change switch position after programming] 6. Set ELECTRONIC TRIGGER THROW ADJUSTMENT to 70% throttle and 30% brake throw (or 7:3). [Adjusts pistol-grip transmitter's throttle trigger throw] Motor and Steering Servo Do Not Work · Check wires, receiver signal harness wiring and color sequence, radio system, crystals, battery and motor connectors, and battery pack. · Possible internal damage­­Refer to Service Procedures. 7. Set MECHANICAL TRIGGER THROW ADJUSTMENT to position with 2/3 throttle and 1/3 brake throw. [Adjusts pistol-grip transmitter's throttle trigger throw] Model Runs Slowly / Slow Acceleration · Check motor and battery connectors­­Replace if needed. · Incorrect transmitter or speed control adjustment­­ Refer to Steps 5 and 6. · Optional external Schottky diode (if used) installed backwards or damaged­­Refer to Step 4. 2. PRESS AND HOLD ESC'S ONE-TOUCH BUTTON With transmitter throttle at neutral, press and hold the ESC SET button until the status LED turns solid red. PULL THROTTLE TO FULL-FORWARD POSITION Hold it there until the status LED turns solid green. NOTE: The motor will not run during programming even if it is connected to the speed control. Motor Runs Backwards · Motor wired backwards­­Check wiring and reverse. [. . . ] PRESS AND HOLD THE ESC'S ONE-TOUCH BUTTON Continue to hold button until the status LED turns solid green. RELEASE THE ONE-TOUCH BUTTON After releasing, status LED will blink red. While the status LED is blinking, PRESS AND RELEASE THE ONE-TOUCH BUTTON. This will select the next profile and the LED will blink the appropriate speed to indicate which profile is selected. [. . . ]