User manual NOVA CONTROLS PRO-FLOW

[. . . ] Pro-Flow Drain Cleaning DISPENSER AND REMOTE PROGRAMMER Reference Manual Installation and Programming Quick Start Guide on Back Cover - Kurzanleitung auf Deckelrückseite - Guide Rapide de Début sur la Couverture Arrière - Guía Rápida de Programación en la Contratapa - Guida Rapida di Inizio é sulla Copertura Posteriore - Guia Rápido de Programação na Contracapa Copyright 2006 Nova Controls, Inc. D Specifications Note Specifications subject to change without notice. Pro-Flow Dispenser Size Weight Total Amperage draw during operation Pump Flow Rate Temperature Humidity Indoor Installation Altitude 5. 18" W x 3. 5" H x 1. 9" D (13. 2 cm W x 8. 9 cm H x 4. 8 cm D) 5. 6 oz. (159 g) 400 mA 6 oz / minute (180 ml / minute) 20° to 150° F (6° to 65° C) maximum 95% relative humidity maximum Approved for indoor use only. (2000m) maximum Battery Pack Size Weight Battery Approximate Battery Life 5. 71" W x 5. 33" H x 1. 55" D (14. 50 cm W x 13. 54 cm H x 3. 94 cm D) 8 oz. [. . . ] After pressing REVIEW: (1) press CHECK to review dispenser formula or (2) press PROG 1, 2 or 3 to review a saved formula. SAVE a formula to a PROG button ­ Press and hold that PROG button for 2 seconds. SEND a saved formula to a dispenser ­ Press the PROG button, then press SEND. (2) to day and time during Clock Set. UP ARROW Increases / Moves Value Forward ENTER / SAVE LEFT ARROW Moves underscore back RIGHT ARROW Underscores next item (1) Add an underscore to change the event you are viewing. (2) Move the underscore to either right or left. Step through the available choices for day, time or dosage. DOWN ARROW Decreases / Moves Value Backward 8 P/N 20-08363-00 Rev. D 3 Formula Programming Overview The Remote Programmer ("the remote") quickly sends formulas/programs to a Pro-Flow dispenser and sets the dispenser's current day and time. The remote also receives and displays information about the dispenser's program and battery life. The installer needs just one remote at all Pro-Flow installations. Note The remote contains a factory pre-set formula, saved as PROG 1, that is suitable for most installations. After setting the current day and time on the remote, the installer need only press the SEND button to load the pre-set formula, date and time into the dispenser. (300 ml. ) of product, dispensed at midnight, seven days per week. Each product dose is called an event (event = day + time + dosage). If desired, the installer can edit the pre-set formula to create new formulas. Up to three formulas (including the factory pre-set) can be saved in the remote. The remote's back-up lithium battery saves clock and formula settings, even when the remote is off or the 9-volt battery is being replaced. Basic Operation of Remote Programmer Turn On: Press the POWER button . (If the battery is low, BAT LOW displays first, then the Home Screen. ) Start from the Home Screen to program a dispenser. Remote turns off automatically after 2 First-Time New Remote Set-up Before using a new remote, you must: 1. If ML is preferred , press and hold the ENTER button , while also pressing Power . Set the 24-hour clock with the local day and time in military format, 00:00 - 23:59. (See "Set the Clock" on page 10 for instructions. ) · Underscored item can be revised. Figure 3-1 Remote's Clock Screen Display HRS P/N 20-08363-00 Rev. Do not leave it in direct sunlight or near high heat. Set the Clock To set the clock on a new Remote Programmer (or to reset the clock to a new time zone): (a). See the Clock screen in Figure 3-1"Remote's Clock Screen Display" on page 9. Press RIGHT arrow to move the underscore to the first number in the TIME. [. . . ] D Communication Between the Remote and Dispenser Send a Formula 1. Making sure that the Remote Programmer is ON, has a clear line-of-sight and is within 4 ft. (1. 2 m) of the dispenser, point the remote directly at the dispenser, and either: (a). Hold the remote in the same location until SET displays on the remote's screen. [. . . ]