User manual NORDICTRACK CLASSIC PRO NTXC80181

[. . . ] NTXC80181 QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing or damaged, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The trained technicians on our customer hot line will provide immediate assistance, free of charge to you. [. . . ] CLEANING THE SKI EXERCISER Wipe your ski exerciser with a clean, dry cloth after each workout to remove perspiration and dirt. Any household window cleaner may be used to clean the chrome and black metal surfaces after each use. Wipe the wood with a clean, dry cloth to remove perspiration and dirt after each use. Use any wood furniture polish or wax to protect the wood finish and prevent drying. The bottoms of the skis may become marked from contact with the drive rollers. For a smooth glide while skiing, carefully rub paraffin wax only on the sides of the skis. The skid plates built into the sides of the skis are designed to wear down and leave a light coating on the sides of the wood. LUBRICATION OF THE RESISTANCE PAD The leather resistance pad on your arm exerciser has been oiled to allow for quiet, smooth braking action. However, the pad will require re-oiling if it dries due to its surroundings. Place a cloth or a piece of plastic underneath the ski exerciser to protect your floor. If the resistance disk (located above the Resistance Pad) has grooves worn into it, it may be necessary to replace it. See the back of this manual for instructions on how to order replacement parts. CARE FOR THE RESISTANCE STRAP AND FLYWHEEL Resistance strap and flywheel maintenance should be performed once a month at the same time. Place a cloth or a piece of plastic underneath the ski exerciser to protect your floor. Wipe the surface of the flywheel with a clean cloth dampened with rubbing alcohol. Slide the "U" Bolt Cover (64) 54 to the right to check the 64 tightness of the 1/4" Nuts 67 (67) on the right side of the Flywheel (54). CAUTION: Do not overtighten the 1/4" Nuts; this can break the "U" Bolt. 39 35 Fully loosen but 32 37 do not remove the Resistance Knob (39). Lift the Pulley (35) and roughen the surface of the leather Resistance Pad (32) with 100-grit sandpaper or a file. Place a pencil between the Pulley and the Resistance Pad and let the oil absorb overnight. 9 9. Note: If the resistance strap is frayed on both sides, it may be necessary to replace it. See the back cover of this manual for information on how to order replacement parts. GENERAL LUBRICATION If the front and rear Rollers (15) begin to squeak, a drop of Oil light household oil may occasionally be needed on the Roller Axles (70). [. . . ] If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone as you exercise. 13 PART LIST--MODEL NO. Qty. Description 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 1 1 1 1 2 2 2 2 2 4 8 4 2 4 1 1 1 1 1 1 1 1 2 4 1 1 2 4 2 2 1 Front Frame Leg Bracket Rear Frame Left Side Board Right Side Board Cross Member Top Board Ski Foot Plate Toe Piece Skid Plate #10 x 5/8" Screw #10 x 1. 25" Screw Kick Pad Roller Upright Upright Knob 5/16" Push Nut 5/16" x 2. 75" Carriage Bolt Reed Switch/Wire Reed Switch Bracket #8 x . 62" Screw Arm Cord Handgrip 1/4" Washer Upright Endcap Upper Body Arm Small Pulley "C" Clip Pulley Axle Resistance Bracket Resistance Pad 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 4 1 1 2 1 1 1 1 2 1 2 2 2 2 1 4 1 2 1 1 1 1 1 2 1 1 4 4 2 1 1 1 #6 x . 62" Screw Resistance Disc Pulley 3/8" Washer Thrust Washer Spring Resistance Knob Snap Buttons Adjustment Knob Hip Pad Slide Round Endcap 5/16" x 1. 75" Carriage Bolt 1/4" Jam Nut 1/4" x 1. 5" Bolt Console Wire #12 x 1" Screw Pulse Monitor Bumper Pad Bracket Pad Cover Hip Pad Flywheel Flywheel Axle Flywheel Bearing Magnet Bracket Magnet . 64" x 1. 19" Washer Large Nylon Spacer Drive Roller w/Bearing #10 Set Screw Axle Clamp w/Set Screw "U" Bolt Cover 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 # # 1 1 2 8 4 4 2 2 2 2 2 2 2 1 9 8 2 2 2 1 1 1 2 1 1 2 1 2 2 2 1 1 1/4" "U" Bolt Console 1/4" Nut #12 x . 55" Screw Small Nylon Spacer Roller Axle Self-Backing Nut 3/8" Washer 3/8" x 5/8" Hex Screw Leg Pin Square Endcap Leg Rubber Foot 5/16" x 2" Hex Head Bolt 5/16" Flange Nut 5/16" x 1. 25" Carriage Bolt Wheel 1/4" x 1. 5" Carriage Bolt 1/4" Hex Nut Resistance Strap Resistance Clamp Resistance Spring Foam Grip Resistance Scale Decal Battery Door Bronze Bushing #10 x 1/2" Screw Incline Clamp Incline Knob Incline Washer Flat Wrench Tool User's Manual Note: "#" indicates a non-illustrated part. See the back cover of this manual for information about ordering replacement parts. 53 45 48 57 59 8 14 11 15 7 13 81 79 5 13 56 6 68 60 61 60 59 68 63 62 25 67 4 12 68 70 71 69 17 80 13 11 11 84 10 8 47 64 65 13 12 9 49 59 6 68 83 69 70 14 15 3 61 60 60 59 58 52 51 56 54 55 26 36 88 39 38 41 37 33 29 32 28 31 48 42 46 9 44 10 43 41 30 90 25 40 50 50 35 87 34 43 33 66 44 31 45 87 29 30 46 89 29 24 90 28 27 23 91 18 80 15 19 21 EXPLODED DRAWING--MODEL NO. NTXC80181 15 7 79 15 79 71 2 1 73 74 94 92 93 85 72 20 22 16 81 82 80 78 17 94 93 92 75 73 72 74 75 76 86 R0902A 77 HOW TO ORDER REPLACEMENT PARTS To order replacement parts, call our Customer Service Department toll-free at 1-888-825-2588, Monday through Friday, 6 a. m. [. . . ]