User manual NISSAN QUEST-2000

[. . . ] It was produced using the latest techniques and strict quality control. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure. In the U. S. , a separate Warranty Information and Maintenance Log Booklet and in Canada, a Warranty and Roadside Assistance Information Booklet explains details about the warranties covering your vehicle and vehicle maintenance schedules. only) will explain how to resolve any concerns you may have with your vehicle, as well as clarify your rights under your state's lemon law. [. . . ] The display will return to the previous radio station, tape or CD that was being played previous to setting the clock in 7 seconds or you may press the RDS/CLK button until the previous display appears. Selecting the desired band Push the AM buttons to change to AM band or push the FM button to change to FM1 or FM2 band reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception. FM-AM Radio operation MUTE button Push the MUTE button to mute out the radio. TUNE buttons WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation. To move quickly through the channels, hold either of the tune buttons down for more than 0. 5 seconds. AUTO SET Press the AUTO button while listening to the radio to activate the auto set feature. When AUTO is depressed for less than 5 seconds, the display window momentarily indicates AUTO ON, and the radio seeks the first six strong stations for the respective band. The first six strong stations are then stored in order in memory buttons one through six. Only stations in the selected band are set, and the station seek begins from the last frequency stored in memory button six. If AM, FM, SCAN, TUNE, SEEK, AUTO or a memory button is pushed while auto set is operating, auto set is canceled and AUTO OFF shows in the display window. AUTO LOAD Press the AUTO button for longer than 5 seconds while listening to the radio to activate the auto load feature. When AUTO is depressed for longer than 5 seconds, the display window momentarily indicates AUTO LOAD, and the radio seeks the first six strong stations for every band. The first six strong stations are then stored in order in memory buttons one through six for each band (AM, FM1, and FM2). SEEK tuning Push the SEEK or buttons to find the next broadcast station. Once the highest broadcast station is reached, the radio continues in the SEEK mode at the lowest station. Once the lowest broadcast station is reached, the radio con- 4-24 Heater, air conditioner and audio systems tinues in the SEEK mode at the highest station. SCAN tuning Push the SCAN tuning button, SCAN illuminates in the display. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for 5 seconds. Pushing the button again during this 5 second period stops SCAN tuning and remains tuned to that station. FM1, or FM2. If the battery is disconnected, or if the radio fuse opens, the radio memory is canceled. In that case, reset the desired stations. RDS (Radio Data System) RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) encoded within a regular radio broadcast. Most RDS stations are currently in large cities, but many stations are now considering broadcasting RDS data. [. . . ] 4-22 Readiness for inspection maintenance (I/M) test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Rear window wiper and washer switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 Registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Remote keyless entry system (See multi-remote control system) . . . . . . . . . . . . . . [. . . ]