User manual NISSAN CUBE 2009

[. . . ] It was produced using the latest techniques and strict quality control. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure. A separate Warranty Information Booklet explains details about the warranties covering your vehicle. The NISSAN Service and Maintenance Guide explains details about maintaining and servicing your vehicle. [. . . ] Once you have adjusted the sound quality to the desired level, push the AUDIO button repeatedly until the normal mode display reappears. Otherwise, the normal mode display will automatically reappear after approximately 5 seconds. CLOCK button: Push the CLOCK button to turn on or off the CLOCK display. Instruments and controls" section for the detailed clock adjustment operation. AUX (Auxiliary)/SAT radio band select: Pushing the AUX button will change between the auxiliary input and the XM Satellite Radio bands (if so equipped) as follows: XM1 ?XM1 The satellite radio mode will be skipped unless an optional satellite receiver and antenna are installed and an XM Satellite Radio subscription is active. See "Radio operation" later in this section for details about using this button for the satellite radio mode. See "AUX (Auxiliary) input" later in this section for details about using this button when connecting this audio system with AUX devices. AUDIO button: Push the AUDIO button to change the selecting mode as follows. Radio operation Radio (FM/AM) band select: Pushing the FM·AM radio band select button will change the band as follows: AM ?AM 4-22 Heater, air conditioner, audio and phone systems When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. When the radio band select button is pushed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. SAT radio band select: The last station played will also come on when the PWR button is pushed to ON. If another audio source is playing when the satellite radio band select button is turned to ON, the audio source will automatically be turned off and the last radio station played will come on. For AM and FM radio Push the SEEK button or to tune from low to high or high to low frequencies and to stop at the next broadcasting station. . For XM Satellite Radio (if so equipped) Push the SEEK button or to tune to the first channel of the next or previous category. If the battery cable is disconnected, or if the fuse opens, the radio memory will be erased. Radio Data System (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data. Music or programming type such as "Classical", "Country" or "Rock". Traffic reports about delays or construction. Push the SCAN button to tune from low to high frequencies and stops at each broadcasting station for 5 seconds. Pushing the button again during this 5 seconds period will stop SCAN tuning and the radio will remain tuned to that station. If the SCAN tuning button is not pushed within 5 seconds, SCAN tuning moves to the next station. to Station memory operations: Eighteen channels can be set for the SAT (if so equipped) band (6 each for XM1, XM2 and XM3), 12 stations can be set for the FM band (6 each for FM1 and FM2), and 6 can be set for the AM band for easy access. Push and hold the desired radio station preset button to until a beep sound is If the station broadcasts RDS information, the RDS icon is displayed. Heater, air conditioner, audio and phone systems 4-23 RADIO DISPLAY change: When the DISP button is pushed during the FM or SAT (if so equipped) radio mode, the radio display will change in the following order. FM radio: Frequency PS/PTY In the FM radio mode, pressing the DISP button will switch the frequency display to the PTY display (if available), and if the DISP button is not pushed again within 5 seconds, it will automatically switch to the PS display. [. . . ] Many insurance companies routinely authorize the use of non-genuine collision parts in order to cut costs, among other reasons. Why should you take a chance? In over 40 states, the law says you must be advised if non-genuine parts are used to repair your vehicle. And some states have enacted laws that restrict insurance companies from authorizing the use of non-genuine collision parts during the new vehicle warranty. These laws help protect you, so you can take action to protect yourself. Insist on the use of Genuine NISSAN Collision Parts! If you want your vehicle to be restored using parts made to NISSAN's original exacting specifications -- if you want to help it to last and hold its resale value, the solution is simple. Tell your insurance agent and your repair shop to only use Genuine NISSAN Collision Parts. [. . . ]