User manual NISSAN ALTIMA-2006

[. . . ] It was produced using the latest techniques and strict quality control. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles (kilometers) of driving pleasure. A separate Warranty Information Booklet explains details about the warranties covering your vehicle. The "NISSAN Service and Maintenance Guide" explains details about maintaining and servicing your vehicle. [. . . ] Clock operation Pressing the CLOCK button displays the clock with the radio on or off. or ) or ) to adjust The display will return to the regular clock display after 7 seconds, or you may press the CLOCK button again to return to the regular clock display. FM/AM/SAT radio operation FM/AM/SAT band select: Pushing the FM, AM or SAT radio select button will change the band to either FM, AM or SAT (satellite-if so equipped) radio stations. When the FM, AM or SAT radio select button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played. The last station played will also come on when the Power/Volume control knob is depressed to ON. No satellite radio reception is available and "NO SAT" is displayed when the SAT button is pressed unless optional satellite receiver and antenna are installed and an XM or SIRIUSTM satellite radio service subscription is active. If a compact disc is playing when the FM, AM or SAT radio select button is pushed, the compact disc will automatically be turned off and the last radio station played will come on. 5. Press the CLOCK button again to exit the clock set mode. 4-30 Display screen, heater, air conditioner and audio systems The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. SCAN tuning stops for 5 seconds at each broadcasting station that has sufficient signal strength. Pushing the SCAN button again during this 5 second period stops SCAN tuning and the radio remains tuned to that station. Station memory operation Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM, FM, SAT (if so equipped ) and FM RDS stations. Press the PRESET ABC button to change between the presets: ABC The radio displays icon A, B or C to indicate which set of presets is active. If the battery cable is disconnected, or if the radio fuse opens, the radio memory is canceled. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) and/or SAT radio encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data. Music or programming type such as "Classical", "Country", or "Rock". If the station broadcasts RDS information, the RDS icon is displayed. WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is pressed, and stops at the next broadcasting station. If using the up button, once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcasting station. If using the down button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station. Display screen, heater, air conditioner and audio systems 4-31 Program type (PTY): PTY can be used to search for a certain program type. Searching or scanning by program type may yield a limited number of selections. When CAT/RPT button is pressed for more than 1. 5 seconds during FM or SAT (if so equipped) mode, the PTY name of the current tuned station is displayed. [. . . ] Also, non-genuine parts often show premature wear, rust and corrosion. It's your right! If you should need further information visit us at: www. nissanusa. com. IN THE EVENT OF A COLLISION Unfortunately, accidents do occur. In this unlikely event, there is some important information you should know. Many insurance companies routinely authorize the use of non-genuine collision parts in order to cut costs, among other reasons. Why should you take a chance? In over 40 states, the law says you must be advised if non-genuine parts are used to repair your vehicle. And some states have enacted laws that restrict insurance companies from authorizing the use of non-genuine collision parts during the new vehicle warranty. [. . . ]