User manual NILFISK SOL 3

[. . . ] Never direct the water jet towards people, pets, electric wiring, or the machine itself. Spray handle and lance are affected by a thrust during operation - therefore always hold the spray lance firmly with both hands. Operator and anyone in immediate vicinity of the site of cleaning should take action to protect himself from being struck by debris dislodged during operation. asbestos, oil) being washed off the object to be cleaned and harming the environment. Do not clean sensitive surfaces made of rubber, fabrics or the like with the zero nozzle. [. . . ] If the handle has not been activated within 20 seconds, the machine will enter stand-by mode. When the machine is not in use, the trigger should be locked with locking device (see arrow). 1 4. 2. 3 Running with hot water The SOLAR BOOSTER is equipped with a heating source (electrical, or diesel driven) to heat the water. The heating source can be switched on or off at convenience by pushing the yellow "Heating" push button (5). Pushing the button once will turn on the lamp in the button and switch ON the heating source. Pushing the button again will turn out the lamp in the button and switch OFF the heating source. the water can be read on the display. 70 C CURRENT TEMP 40 C + OK 3 4 5 SOLAR BOOSTER will monitor the water temperature and regulate the heating source to provide the preset temperature. On EH-models, with heating tanks on the suction side of the high pressure pump, heating will be performed independently of the spraying operation - "Working mode" as well as "Standby mode". The temperature is controlled by a temperature sensor in the water tank. Thus the water will always be preheated to the desired value ­ ready for use when the spray handle is activated. Heating is controlled by a thermostat on the outlet of the boiler when water 17 0° C° 20° 40° 85° 80° 60° 8 On the D-model the temperature can be adjusted within the limits stated on the "Thermostat" (8), by turning the knob to the desired value. When the heating source is ON (push button (5) alight), the preset and the actual outlet temperature of is flowing out of the SOLAR BOOSTER ­ "Working mode". 70°C, whereas grease and fat is easiest to remove with temperatures of 80 to 85°C. Several detergents become more efficient when acting with hot water ­ please refer to manufacturers recommendations. 5. 4 Mechanical impact In order to break down tough layers of dirt, additional mechanical impact may be required. Special lances with special nozzles (pulsating jet / concentrated "0" jet) are available for such purposes as are rotating brushes plus soft & sand blasting equipment. Please ask your Nilfisk-ALTO representative. 20 5. 5 Detergents As standard the system is delivered without a detergent injector and the optional, factory mounted, internal chemical system. If you want to use detergents or disinfectants these should be dosed through an external injector (see section 4. 1. 5) or through the pump (see section 4. 1. 6). The most efficient cleaning is reached with detergents in conjunction with the high pressure cleaning. For that purpose Nilfisk-ALTO can offer you a series of products specially developed for high pressure cleaning, among other fields within: · · · · Cleaning of vehicles, machines, stalls etc. Disinfection Degreasing of workpieces Descaling Contact your Nilfisk-ALTO distributor for directions as to which product(s) will fulfil your requirements. The method of application and the dosage of the individual products appear from the product labels or the data sheet. Low-foaming detergents are applied through an injector and under low pressure. A change to cleaning under high pressure is effected by regulating from »low pressure mode« to »high pressure mode« on the double spray lance or by attaching a high pressure spray lance. [. . . ] that repairs have not been carried out or attempted by other than Nilfisk-ALTOtrained service staff. that the product has not been exposed to abuse such as knocks, bumps or frost. malfunctions due to causes mentioned in section "7. 0 Trouble shooting" of the instruction manual). · · A warranty repair comprises the replacement of defective parts, but it does not cover freight and packaging charges. Besides we refer to national Sale of Goods Act. 10 Declaration of Conformity Declaration of Conformity The undersigned, representing the following manufacturer, Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej 1, DK-9560 Hadsund declares that the product: · · · High Pressure Washer · · · type : SOL 3, EH is in conformity with the provisions of the following EC directives, with subsequent amendments: 2006/42/EC, 2006/95/EC, 2004/108/EC and furthermore declares that the following harmonised standards have been applied: EN 60335-2-79 (2006), EN 55014-1 (2006), EN 55014-2 (2001), EN 61000-3-2 (2006) The following (parts/clauses of) national technical standards and specifications have been used: DS EN 60335-2-79 Hadsund, 2008-10-01 Anton Sørensen V. P. [. . . ]