User manual NILFISK SCRUBTEC R 371 C

[. . . ] / Rok výroby / Baujahr / Fabrikationsår / Año de fabricación / Väljalaskeaasta / Année de fabrication / Valmistusvuosi / Year of construction / / Gyártási év / Anno di costruzione / Pagaminimo metai / Izgatavosanas gads / Byggeår / Bauwjaar / Ano de fabrico / Rok produkcji / Anul fabrica iei / / Tillverkningsår / Rok výroby / Leto izdelave / Leto izdelave/ømal yÕlÕ : , The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. Caractéristiques techniques avec tête porte-brosses/plateaux support disque Description Diamètre brosse / disque Poids sans batteries et avec réservoirs vides Poids maximum avec batteries et réservoirs pleins Puissance moteur brosse / plateau support disque Vitesse de rotation brosse / plateau support disque Pression brosses/plateaux support disque avec extra-pression désactivée Pression brosses/plateaux support disque avec extra-pression activée SCRUBTEC R 361 305 mm SCRUBTEC R 366 330 mm 197 kg 478 kg 2 x 400 W 190 tr/mn 30 kg 50 kg SCRUBTEC R 371 355 mm REMARQUE Pour un lavage / séchage correct du sol près du mur, Alto recommande d'approcher le côté droit de la machine, comme illustré sur la figure 2. The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal. [. . . ] Turn the selector (C) to WET or GEL according to the type of batteries installed. Open the covers (51 and 58) and check that the tanks (60 and 61) are empty, otherwise empty them through the drain hose (10) and the tap (24). If a battery box is installed, place it on the left side of the machine, to allow the tank assembly (71) to be closed correctly. When starting the machine, check that between the deck (4 or 5) and the machine, or between the squeegee (12) and the machine, there is no foreign material which may prevent the deck or squeegee from lifting. This check is necessary because, if the machine has been turned off without lifting the deck and the squeegee, the deck and the squeegee will lift automatically at next machine start-up. The machine can be equipped with either the brush/pad-holder deck (4) or the cylindrical brush deck (5). for deck installation/removal see the procedure in Maintenance chapter. NOTE When the deck is installed/removed, it may be necessary to change the squeegee too, because they must have the same width. According to the kind of cleaning to be performed, the machine can be equipped either with brushes (88) or pad-holders (89) with pads (90) together with the appropriate deck. Before turning on the switch (34), always check that between the deck (4) and the machine there is no foreign material which may prevent the deck from lifting. Install the brushes/pad-holders (88 or 89) and lift them completely, then turn them clockwise (see the arrows 88 and 89) until the end of stroke. Before turning on the switch (34), always check that between the deck (5) and the machine there is no foreign material which may prevent the deck from lifting. Install the squeegee (12) and fasten it with the handwheels (15), then connect the vacuum hose (11) to the squeegee. Adjust the squeegee with the handwheel (16) so that the rear blade (18) touches the floor along all its length and the front blade (17) is slightly lifted from the floor. Fill the solution tank (61) with a solution suitable for the work to be performed. Do not fill the solution tank completely, leave a few centimetres from the edge. Always follow the dilution instructions on the label of the chemical product used to prepare the solution. Using the lever (1), adjust the inclination of the steering wheel (2) to reach a comfortable position. Turn the ignition key (41) to "I" and press the forward/reverse gear pedal (3). If the yellow or red warning light (37b or 37c) turns on, turn the ignition key back to "0" and charge the batteries (see the procedure in Maintenance chapter). Drive the machine to the working place, by starting it with the hands on the steering wheel and by pressing the pedal (3). The drive speed can be adjusted from zero to maximum speed according to the pressure on the pedal (3). [. . . ] Pay careful attention when charging the batteries as there may be battery fluid leakages. If it comes in contact with skin or eyes, rinse thoroughly with water and consult a physician. Open the covers (51 and 58) and check that the tanks (60 and 61) are empty, otherwise empty them through the drain hose (10) and the tap (24). When the correct level is reached, close the caps (75) and clean, if necessary, the upper surface of the batteries. [. . . ]