User manual NILFISK S3B

[. . . ] This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. Before starting up your machine please check it carefully for any defects. If you find any, do not start up your machine and con- tact your Nilfisk distributor. [. . . ] Front position is to be used if the product is used together with a special wall hook for wall storage. 3. 3 Mounting of hose reel handle (only models with hose reel) 1. Click the hose reel handle on to the trolley handle (no screws). 6 Nilfisk S3B / P 150. 2 / P 160. 2 3. 4 Mounting of quick coupling 1. Note: The inlet filter must always be fitted in the water inlet pipe to filter out sand, limestone and other impurities as these will damage the pump valves. EN 3. 5 Mounting of high pressure hose Caution: Failure to fit the filter will invalidate the guarantee. Attach the high pressure hose (4) to the spray handle (7). Detach the high pressure hose by pressing the pawl. 4 Operating your pressure washer 4. 1 Connection of high pressure hose Machines without hose reel: Attach the high pressure hose (4) to the high pressure connection of the machine (3). Machines with hose reel: Unwind the high pressure hose completely. 7 Nilfisk S3B / P 150. 2 / P 160. 2 EN 4. 2 Mounting of spray lance and nozzles 1. Push the spray lance (6) into the spray handle (7) and twist it until the bayonet coupling locks into position. Attach the nozzle. 4. 3 Water connection An ordinary 1/2" garden hose of min. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is clean and free from debris. Connect the water hose to the water supply by means of the quick connector (inlet water, max. Turn on the water. NOTE: Connection to the public mains according to regulations. 4. 4 Telescopic handle The machine features a telescopic handle. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning. EN 5. 1. 1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid "super clean" areas, where the detergent collects in higher concentration and streams downwards. Same method as for flagstones, but be careful - bad joints and wood may be damaged by high pressure. Adjust the distance (pressure) to the quality of the joints and the wood. Patio Cleaner can also be used on vertical surfaces. Rims, aluminium Rim brush, atomizer, Alu Cleaner Powerspeed® nozzle, Stone & Wood Cleaner, Patio Cleaner Wood Cleaner Garden brush Flagstones, concrete floors and other hard surfaces Garden furniture, wood Brickwork, Powerspeed® Wood nozzle, work Stone & Wood Cleaner, Patio Cleaner Gutter Underchassis spray Wash the gutter with the underchassis spray lance. ½ m (to mark) into a tube or drain and activate the trigger of the spray handle. The nozzle opening turning backwards will pull the cleaner through the tube. The nozzle will break down the , , plug" and flush the dirt backwards. Mount the water/sand blasting equipment and rust and paint is efficiently and quickly removed. You may use Stone & Wood Cleaner to remove moss and algae. Cleaning Tube cleaner of drain pipes, outlets, down pipes etc. [. . . ] Any repair should always be made in an authorized workshop with original spare parts. 7. 1 Cleaning of water inlet filter Clean the water inlet filter regularly once a month or more frequently according to use. The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves. CAUTION: Failure to fit the filter will invalidate the guarantee. 7. 2 Cleaning of nozzle A clogging up in the nozzle causes a pump pressure which is too high. IMPORTANT: The cleaning tool (11) should only be used when the nozzle is detached! [. . . ]