User manual NILFISK RS 851

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. 00 level RVI RXD VOLVO VDS2 CAT-TO 2 ALLISON C-4 ZF TE ML 04C DEUTZ DQC IV 05 level ISOTTA FRASCHINI Betankungsdaten Kapazität Kraftstofftank Kapazität Öltank Hydraulikanlage Daten elektrische Anlage Anlagenspannung Anlassbatterie Werte 65 Liter (17, 2 USgal) 55 Liter (14, 5 USgal) Werte 12 V 12 V ­ 100 Ah Zulassungen und Spezifikationen CUNA NC 956-16 97 FF. 00 level RVI RXD VOLVO VDS2 CAT-TO 2 ALLISON C-4 ZF TE ML 04C DEUTZ DQC IV 05 level ISOTTA FRASCHINI Données ravitaillements Capacité réservoir carburant Capacité réservoir huile système hydraulique Données système électrique Tension système Batterie de démarrage Valeurs 65 litres (17, 2 US gal) 55 litres (14, 5 US gal) Valeurs 12 V 12 V ­ 100 Ah Approbations et spécifications CUNA NC 956-16 97 FF. This Manual is an integral part of the machine; its purpose is to provide the operator with all necessary information to use the machine properly in a safe and autonomous way. [. . . ] The machine is equipped with an automatic system that, when the operator is on the driver's seat (14, Fig. E) to use the rear pipe, water can be supplied by the nozzles using the water pump switch (27, Fig. D) and gradually pressing the pedal (26), on the front side to move forward and on the rear side to move backward. The drive speed can be adjusted from zero to maximum speed by increasing the pressure on the pedal. While working, the machine picks up both light materials such as dust, paper, leaves, etc. The machine is equipped with a safety system that stops the movement (machine in neutral) and disables the hydraulic functions controlled by the joysticks (15 and 36, Fig. The movement and the hydraulic functions restarts automatically when the operator returns on the driver's seat (14). Only the suction fan for the manual rear pipe, and the high-pressure pump for the washing system can be used in these conditions. If necessary, shift the 3rd broom arm to working mode, by moving the joystick (15, Fig. NOTE The machine is equipped with an automatic switch that stops the water supply to the nozzles when the broom rotation has been stopped by pressing the switch (29, Fig. D) and the water supply has not been previously stopped by pressing the switch (27). E) to idle, and hold it in this position for a few minutes to let the system stabilize. If necessary, bring the 3rd broom safety arm from the position (2, Fig. Avoid stopping for a long time with the machine in the same position and the brooms rotating: this could create unwanted marks on the floor. When necessary, in working mode, shift the suction inlet and side brooms to the left or to the right by pressing the pushbuttons (41 or 42, Fig. When necessary, in working mode, shift the 3rd broom to the left or to the right by moving the joystick (15, Fig. Note that, while the skirt is lifted, the machine suction power decreases. If necessary, to collect bulky debris, it is also possible to remove the front skirt (25, Fig. G); remove it according to the following procedure: · Lift the side brooms, then stop the machine and turn off the engine. Install the skirt (3) in the reverse order of removal, after stopping the machine and turning off the engine. If necessary, shift the 3rd broom arm to working mode, by moving the joystick (15, Fig. If the machine must be transferred to an appointed dumping area, engage the parking brake (13, Fig. [. . . ] NOTE This is a basic procedure, it is often recalled during other procedures, when necessary. This procedure is applicable only for sweepers with appropriate fittings for installation of snow brush. Operating according to the safety rules, with a proper hoisting system (1, Fig. Move the pipes and cable aside, to avoid squashing them during the lifting operation. [. . . ]