User manual NILFISK POSEIDON 2-24 PORTABLE

[. . . ] Before use, check that the highpressure washer is safe and in proper condition. Regularly check whether the power cord is damaged or shows signs of ageing. Use the high-pressure washer only when the mains power lead is in a safe condition. Check the rated voltage of the high-pressure washer before connecting it to the mains power supply. [. . . ] If the power cord is damaged, it must be replaced by authorized Service or an electrician to avoid danger before use of the washer is continued. Please contact the Service department or an authorised specialist work-shop for all other maintenance or repair work! Operation CAUTION!Always unwind cord from the reels completely to prevent the power cord overheating. When using an extension cord, connectors must be of watertight construction. When using an extension cord, check the minimum cross-sections of the cable: Cable length m up to 20 m 20 to 50 m Cross section <16 A <25 A ø1. 5mm² ø2. 5mm² ø2. 5mm² ø4. 0mm² Do not damage the mains power lead (e. g. Disconnect the power cord by pulling the plug only (do not pull or tug the power cord). Electrical equipment CAUTION!Never spray electrical equipment with water: danger for persons, risk of short-circuiting. The washer may only be connected to a correctly installed plug socket. Voltage fluctuations should not occur if the impedance at the transfer point is less than 0. 15. If in doubt, ask your local electricity supplier. Safety Devices Unloader valve Unacceptably high pressure is fed back without residual pressure via a bypass line into the intake line of the pump when the safety device is tripped. The unloader valve is set and sealed at the factory and must not be adjusted. 45 2 Description 2. 1 Purpose This high-pressure washer has been designed for professional use within ­ Trade ­ Construction industry ­ Small-scale farming Always use the washer as described in these operating instructions. Any other use may damage the washer or the surface to be cleaned or may result in severe injury to persons. 2. 2 Operating elements See fold-out page at front of these operating instructions. Handle Mains power lead Spray handle High-pressure hose Spray lance Supply water connection with water inlet filter 7 High pressure hose connection 8 Main switch 1 2 3 4 5 6 46 3 Before starting the washer 3. 1 Setting up the washer Max. Before using the washer for the first time, check it carefully to detect any faults or damage. NOTE: Set the machine in upright position when checking the pump oil. 3. 2 Connecting the high pressure hose 1. Screw the quick connector of the high pressure hose onto the nipple on the washer (7). 3. 3 Connecting the water supply ­ briefly to a pipe interrupter with moving section ­ with a free outlet See chapter 8. 3 Technical Data for required quantity of water and water pressure. In the case of poor water quality (sand, etc. ), we recommend that a fine water filter is fitted in the water inlet. Rinse the water supply hose briefly in order to prevent sand an other dirt particles entering into the machine. Open water tap. Do not connect the washer directly to the public drinking water mains. Observe the regulations of your water supply company to prevent backflow of water into the supply line. A connection is permitted, however: 47 3. 4 Electrical connection 1. Put the plug into the electrical socket. 4 Operation 4. 1 Connecting the spray lance to the spray handle 1. Pull the blue quick-release grip (A) of the spray handle forwards and lock it by turning it to the left. [. . . ] permissible suction height has not been heeded · · · · > · The motor does not start when the washer is switched on > The plug is not inserted properly, · i. e. there is no current Check the plug, lead and switch and if necessary have them replaced by a trained electrician Switch on the mains fuse Have the electrical connection checked Contact the customer service Use lead with correct cross section or length Check that the mains voltage and the washer voltage are the same. Switch off the washer and allow it to cool for at least 3 minutes Change the high-pressure nozzle Switch off the machine > When the washer is switched on the motor buzzes without starting > > > The motor switches off > The mains fuse is switched off The mains voltage is too low The pump is blocked or frozen Incorrect cross-section or length of the extension lead The overload protection has been activated due to overheating or overloading of the motor · · · · · > Water outflow under the machine > High-pressure nozzle is dirty Machine runs longer than 3 minutes with spray handle closed · · 8 Further information 8. 1 Recycling the washer Make the old cleaner unusable immediately. As specified in European Directive 2002/96/EC on old electrical and electronic appliances, used electrical goods must be collected separately and recycled ecologically. [. . . ]