User manual NILFISK FLOORTEC 560 B

[. . . ] www. nilfisk-alto. com FLOORTEC 560 B DEUTSCH FRANÇAIS ENGLISH NEDERLANDS BETRIEBSANLEITUNG MANUEL D'UTILISATION USER MANUAL GEBRUIKSAANWIJZING B 2 9 3 D 4 5 E 9 9 8 7 9 6 1 S310027 S310028 F S310025 G C 5 18 25 19 20 23 14 16 12 24 7 27 5 3 S310029 S310030 H I 4 17 8 2 6 5 J S310081 S310032 K 10 26 9 15 22 13 8 21 11 S310080 S310082 S310034 USER MANUAL ENGLISH INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MANUAL PURPOSE AND CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TARGET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HOW TO KEEP THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fill up each battery element with sulphuric acid for batteries (density from 1. 27 to 1. 29 Kg at 25°C) in accordance with the instructions specified in the Battery manual. The correct quantity of sulphuric acid is indicated in the Battery Manual. Let the battery rest and fill in with sulphuric acid in accordance with the instructions specified in the Battery manual. Proceed with battery recharging (see the procedure in the Maintenance paragraph). Machine setting 1. The machine setting performed at the factory is for lead (WET) batteries. If this setting corresponds to the type of battery installed on your machine, go to the next paragraph, otherwise perform the following operations: 4. T) on the "WET" connectors (2) for lead battery or on the "GEL" connectors (3) for gel battery. Proceed with recharging the batteries (see the procedure in the Maintenance paragraph). BEFORE START-UP WARNING!C) is correctly closed before starting up the machine. 6 FLOORTEC 560 B 146 2590 000(1)2005-03 A USER MANUAL STARTING AND STOPPING THE MACHINE At every start-up 1. B) in the control panel; turn it to "I" position [without pulling the lever (4, Fig. Proceed with recharging the batteries (see the procedure in the Maintenance paragraph). C), disengage the handle (12) from its retainer (2) and lower the handle (without turning it). NOTE The side broom (10, Fig. B) to "I" position without pulling the selector lever (4, Fig. B) take the ignition key to "0" position, then charge the battery. The speed is proportional to the pressure applied to the selector lever (4, Fig. Avoid stopping for a long time with the machine in the same position and the brooms rotating: this could create unwanted marks on the floor. To collect light and bulky waste materials, lift the front skirt by pulling the lever (27, Fig. C); do not keep pushing onto the lever for a long time in order not to reduce the suction capability of the machine). For the machine to sweep properly the dust filter must be as clean as possible. To clean the filter while sweeping, activate the filter-shaker proceeding as follows and according to the type of filter-shaker installed: ­ Manual filter-shaker: turn the ignition key to "0" position, pull the handle outward (20, Fig. The internal return spring strikes the dust filter frame and shakes it. ­ Electric filter-shaker (optional): press and hold the filter-shaker button (8, Fig. [. . . ] 7. Battery charging with optional battery charger supplied with the machine 1. (Only for lead battery) check the correct level of electrolyte inside the battery; if it is necessary top up through the caps (8, Fig. When the correct level is reached, clean, if necessary, the upper surface of the battery. Check that the voltage and frequency shown on the machine serial number plate (1, Fig. [. . . ]