User manual NILFISK CONTRACTOR

[. . . ] Gebruikershandleiding . . . . . . . . . . . . . 1 13 25 37 49 61 73 - 12 24 36 48 60 72 84 Congratulations! We'd like to say, "Thank You" for choosing the CONTRACTOR DIESEL. This instruction manual is provided with your new High Pressure Washer to ensure that you obtain the best results, in the safest manner, with your new machine. Contents EN IMPORTANT This machine is a High Pressure Washer, capable of producing 2600 psi (180 bar). A complete understanding of the material in this manual will help you avoid possible injury or damage to other objects, as well as damage to the machine, itself. It's also important that you read the Ruggerini engine manual provided, before you begin to use this machine. [. . . ] Open the small venting cap on the "Jerry-can" if you intend to operate in hot water or steam mode. Start the Ruggerini engine as described in the enclosed operating instructions. The key for the electric start has the following 3 positions: 1 "0" off 2 "I" run 3 the startkey will return to position 2 when released. This can be taken from the pressure gauge and must not exceed 180 bar (2600 psi). (See section 14. 0). EN d) Start the machine, if stopped, and activate the spray handle to start the burner. IMPORTANT: For safety reasons it is important that instruction (a), above, always be followed!Note: If the engine stops immediately after having been started up, it should be checked whether the throttle control is set at idle speed. If it is, the throttle control should be adjusted to full speed. 9. 4 Adjustment of pressure and water volume High pressure/volume In order to achieve maximum working pressure the pressure adjustment knob (pos. 27) on the lance should be turned all the way in (clockwise until completely closed) and the volume adjustment knob (pos. 22) situated on the front of the pump should be turned all the way out (counterclockwise). Low pressure/volume To reduce the working pressure, turn the pressure adjustment knob (pos. 27) on the lance, counterclockwise until the desired result is achieved. Turn the volume adjustment knob on the front of the pump, clockwise, reducing water flow and volume. Test the results, and repeat the process until you have achieved the results you wish. By varying the settings of the pressure adjustment knob on the lance, and the volume adjustment knob on the pump, you may obtain pressures from 4 bar (60 psi) to 180 bar (2600 psi), and water flows from 6 l/min. (5. 4 US gpm). 9. 2 Cold water operation After the starting up procedure the machine is ready for cleaning with cold water. 9. 3 Hot water/Steam operation Hot water: Adjust the thermostat (pos. Steam: a) Adjust to temperatures above 95°C (200°F) ONLY with the trigger on spray handle released. c) Adjust the thermostat to the required temperature, 95-150°C (200-302°F). 44 9. 5 Shutdown WARNING: Danger of burn Do not disconnect the high pressure hose until you have completed the following steps (risk of injury): 1. Spray cold water until the water temperature is under 50°C (122°F). Squeeze the trigger of the spray handle for a short time to empty the system of water. Disconnect the high pressure hose. 10. 0 Storage/frost proofing It is advisable to store the machine in a frost proof place between operations. [. . . ] 1 ) Delta t= 52°C/126°F This machine has been manufactured in accordance with the EMC directive 89/336/EEC inclusive of subsequent amendments. Specifications are subject to alterations. 48 FINLAND Nilfisk-Advance Oy Ab Piispantilankuja 4 02240 Espoo Tel. : +358 207 890 600 Fax: +358 207 890 601 E-mail: asiakaspalvelu. fi@nilfisk. com POLAND Nilfisk-Advance Sp. 3-go MAJA 8 Tel. : +48 22 738 37 50 Fax: +48 22 738 37 51 E-mail: info@nilfisk-alto. pl FRANCE PORTUGAL Nilfisk-ALTO Division of Nilfisk-Advance Lda. Sintra Business Park Zona Industrial Da Abrunheira Edificio 1, 1° A P2710-089 Sintra Tel. : +35 808 200 537 Fax: +35 121 911 2679 E-mail: mkt@nilfisk-advance. es http://www. nilfisk-alto. com HEAD QUARTER DENMARK Nilfisk-Advance Group Sognevej 25 DK-2605 Brøndby Tel. : (+45) 4323 8100 Fax: (+45) 4343 7700 E-mail: mail. com@nilfisk-advance. com Nilfisk-ALTO ALTO France SAS Aéroparc 1 19 rue Icare 67960 Entzheim Tel. : (+33) 3 88 28 84 00 Fax: (+33) 3 88 30 05 00 E-mail: info. fr@nilfisk-alto. com GERMANY Nilfisk-ALTO Division of Nilfisk Advance Guido-Oberdorfer-Str. [. . . ]