User manual NILFISK CA 551

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. Tableau de bord Guidon Câble d'alimentation Support câble d'alimentation Goulot arrière de remplissage solution Tuyau extractible pour remplissage à l'eau (optionnel) Levier de soulèvement/abaissement embouchure Pédale de soulèvement/abaissement tête Pédale en position de tête soulevée Pédale en position de tête baissée Roue arrière de direction Roues avant sur essieu fixe Tuyau d'aspiration embouchure Tuyau de vidange eau de récupération Tuyau de niveau et de vidange solution Tête porte-brosses/plateaux support disque Brosse/plateau support disque Réservoir solution Réservoir eau de récupération Couvercle réservoir eau de récupération Porte-objets Elastique porte-documents (optionnel) Embouchure 22. Tête porte-brosse/plateau support disque (14) - Y est installé la brosse ou le plateau support disque et le moteur correspondant. Brosse/plateau support disque (15) - Il est possible d'installer une brosse ou un plateau support disque avec disque. [. . . ] Use brushes and pads supplied with the machine and those specified in the User Manual. in case of machine malfunctions , ensure that these are not due to lack of maintenance. Otherwise, request assistance from the authorised personnel or from an authorised Service Center. Has been left outdoors exposed to bad weather conditions · Is wet or has been dropped into water turn it off immediately and contact the Nilfisk-Advance Service Center or a qualified technician. If parts must be replaced, require ORIGINAL spare parts from a Dealer or Authorised Retailer. To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of this Manual, must be performed by the authorised personnel or by an authorised Service Centre. Carefully read all the instructions before carrying out any maintenance/repair procedure. Do not wash the machine with direct or pressurised water jets, or with corrosive substances. The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, electronic components, etc. ), which are subject to standards that require disposal in special centres (see the Scrapping chapter). Control panel Handlebar Power supply cable Power supply cable holder Solution rear filler neck Water removable filler hose (optional) Squeegee lifting/lowering lever Deck lifting/lowering pedal Pedal position when deck is lifted Pedal position when deck is lowered Rear steering wheel Front wheels on fixed axle Squeegee vacuum hose Recovery water drain hose Solution drain and level check hose Brush/pad-holder deck Brush/pad-holder Solution tank Recovery water tank Recovery water tank cover Can holder Document retainer (optional) 21. Squeegee Squeegee mounting handwheels Squeegee balance adjusting handwheel Solution filter Solution tap Recovery water tank cover (opened to be cleaned) Recovery water tank cover (completely opened) Tank cover gasket Cover movable retaining plate Cover fixed retaining plate Compensation hole Serial number plate/technical data/conformity certification Plug for squeegee vacuum hose cleaning Vacuum grid with automatic shut-off float Solution front filler neck Foam filter Recovery water tank retaining plate Machine straight forward movement adjusting handwheel Machine forward speed adjustment handwheel Solenoid valve Control panel (1) - It is the area where machine controls are located, see Control and Switch Description paragraph. Power supply cable holder (4) - Use it to roll up the power supply cable when it is not in use. Water removable filler hose (optional) (6) - For easily filling the tank with water. Deck lifting/lowering pedal (8) - It has the following functions: (8a) Pedal position when deck is lifted (8b) Pedal position when deck is lowered Rear steering wheel (9) - It allows the machine to steer. Solution drain and level check hose (13) - It is equipped with level marks to check the solution level in the tank. Do not cover these plates for any reason and immediately replace them if they are damaged. Do not press the switch (51) too much, otherwise the machine will start. To remove the brush/pad-holder lift the deck by pressing the pedal (8), then manually remove the brush/pad-holder from the hub, by turning it in the opposite direction to the normal rotation direction. Install the squeegee (21) and fasten it with the handwheels (22), then connect the vacuum hose (11) to the squeegee. With the handwheel (23), adjust the squeegee so that the rear blade - in all its length - touches the floor and the front blade is slightly detached from the floor. Use the filler neck (5) to fill the tank (16) with a solution suitable for the work to be carried out. [. . . ] 2 or 3) of the front blade (C) and the edges (F) of the rear blade (D) lay down on the same level, along their length; otherwise adjust their height according to the following procedure: ­ Release the tie rod (G, Fig. 2 or 3), then tighten the wing nuts, or engage the retainers, and then engage the tie rod. 2 or 3) and rear blade (D) for integrity, cuts and tears; if necessary replace them according to the following procedure. Check that the front corner (J) of the rear blade is not worn; otherwise, overturn the blade to replace the worn corner with an integral one. [. . . ]