User manual NILFISK BR751

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. Tête porte-brosses/plateaux support disque Moteurs des brosses/plateaux support disque Connecteur tête porte-brosses/plateaux support disque ou tête porte-brosses cylindriques Tuyau d'alimentation solution aux brosses (optionnel) Bouton de fixation tête Goupilles tête Support tête Brosse Plateau support disque Disque Connecteur tête porte-brosses cylindriques Couvercle de protection connecteur Tête porte-brosses cylindriques Moteurs brosses cylindriques Volet latéral tête porte-brosses/plateaux support disque Volet latéral tête porte-brosses cylindriques Bouton supérieur de fixation volet Bouton inférieur de fixation volet Brosse cylindrique Portillons brosses cylindriques Boutons de fixation portillons Conteneurs déchets brosses cylindriques Poignée conteneur déchets Caractéristiques techniques avec tête porte-brosses/plateaux support disque Description Diamètre brosse Poids sans batteries et avec réservoirs vides Poids maximum avec batteries et réservoirs pleins Puissance moteur des brosses/plateaux support disque Vitesse de rotation brosse/plateau support disque Pression brosse/plateau support disque sans extra-pression activée Pression brosse/plateau support disque avec extra-pression activée Description Dimensions brosse cylindrique (diamètre x longueur) Poids sans batteries et avec réservoirs vides Poids maximum avec batteries et réservoirs pleins Puissance moteur brosse cylindrique Vitesse de rotation brosses cylindriques Pression brosses cylindriques BR 601 305 mm BR 651 330 mm 140 Kg 385/470 Kg 400 W 190 tr/mn 30 Kg 50 Kg BR 751 370 mm The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal. Before carrying out any procedure on the machine, the operators and qualified technicians must read this Manual carefully. [. . . ] C) and the machine there is no foreign material which may prevent the deck from lifting. K) and lift them completely, then turn them clockwise (see the arrows in Fig. I) and check that the tanks (15 and 16) are empty, otherwise drain them through the drain hose (10, Fig. If a battery box is installed, place it on the left side of the machine, to allow the tank assembly (1, Fig. C) and the machine there is no foreign material which may prevent the deck from lifting. Do not fill the solution tank completely, leave few inches from the edge. Always follow the dilution instructions on the label of the chemical product (detergent) used to create the solution. Do not fill the washing water tank completely, leave a few inches from the edge. C) and fasten it with the handwheels (15), then connect the hose (11) to the squeegee. C), adjust the squeegee so that its rear blade (18) - in all its length - touches the floor and that the front blade (17) is slightly detached from the floor. I) with a detergent suitable for the work to be carried out (highly concentrated detergents). Do not fill the detergent tank completely, leave a few inches from the edge. ), in order to fill the hose quickly, it may be useful to drain the EDS-ECO Dosage Solution once or several times (see the procedure in Maintenance chapter). C), adjust the inclination of the steering wheel (2) to reach a comfortable position. B) turns on, turn the key back to "0", then charge the batteries (see the procedure in Maintenance chapter). Drive the machine to the working area, by keeping the hands on the steering wheel and pressing the pedal (3, Fig. C) on the front side to move forward and on the rear side to move backward. The drive speed can be adjusted from zero to maximum speed according to the pressure on the pedal (3, Fig. C) is equipped with a safety sensor, which allows the machine to be moved with the pedal (3, Fig. NOTE The machine is equipped with an anti-tilting safety system that reduces the speed when turning, irrespectively of the pressure on the gear pedal. The reduction of speed when turning is not a malfunction but a characteristic that improves the machine stability in every condition. If necessary, adjust the working speed using the maximum speed adjuster (11, Fig. [. . . ] Pay careful attention when charging the batteries as there may be battery fluid leakages. If it comes in contact with the skin or eyes, rinse thoroughly with water and consult a physician. I) and check that the tanks (15 and 16) are empty, otherwise drain them through the drain hose (10, Fig. C) to the electrical mains (voltage and frequency must be compatible with the battery charger values on the machine serial number plate). [. . . ]