User manual NILFISK BR 1100S SBG SPECIAL 3-10

[. . . ] BR 1100S SBG SPECIAL Instructions For Use Original Instructions MODEL: 56380640 3/10 FORM NO. 56091001 A-English A-2 / ENGLISH TABLE OF CONTENTS page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 Know Your Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 ­ A-5 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The detergent cartridges have a white decal on them so you can write the detergent name on each cartridge to avoid mixing them up. The system should be purged of previous detergent when switching to a different detergent. When installing a new cartridge, remove the Cap (AA) and place the cartridge in the detergent box. Install the Dry Break Cap (BB) and detergent hose as shown. FIGURE 5 FORM NO. 56091001 - BR 1100S SBG SPECIAL - A-11 A-12 / ENGLISH DETERGENT SYSTEM PREPARATION AND USE (ECOFLEX MODELS ONLY) FIGURE 6 PURGE Press (J) & (F) for 3 seconds to purge. A-12 - FORM NO. 56091001 - BR 1100S SBG SPECIAL ENGLISH / A-13 OPERATING THE MACHINE Be sure you understand the operator controls and their functions. Follow the instructions in preparing the machine for use section of this manual. 1 2 3 4 5 See Figure 7. While seated on the machine, adjust the seat and steering wheel to a comfortable operating position using the adjustment controls (23) and (5). Reference the Battery Condition Indicator (K5) and Hour Meter (K3) before proceeding. To transport the machine to the work area, apply even pressure with your foot on the front of the Drive Pedal (8) to go forward or the rear of the pedal for reverse. Press the Solution Switch (F) and hold for 5 seconds to pre-wet the floor. NOTE: This will help prevent scarring of the floor surface when starting to scrub with dry brushes. Press the Scrub ON Switch (D) once for Regular Scrub, twice for Heavy Scrub or three times for Extreme Scrub mode. Both the solution flow and detergent (EcoFlex models) flow have 3 presets that coincide with the 3 scrub modes (see Control Panel). NOTE: There is a solution flow rate override function if you wish to increase solution flow without increasing scrub pressure. Hold the Solution Switch (F) for 3 seconds (solution indicator will start flashing) and then let go. You then have 3 seconds to set a different flow rate by simply pressing the Solution Switch (F) repeatedly until the Solution Flow Indicator (K1) shows the rate you desire (1-5 / see Control Panel). Any subsequent scrub pressure adjustments will reset the solution flow rate to default. NOTE: The scrub, solution, vacuum, detergent (EcoFlex models) and side broom (cylindrical models) systems are automatically enabled when the Scrub ON Switch (D) is pressed. Any individual system can be turned OFF or back ON by simply pressing its switch at any time during scrubbing. When the Scrub ON Switch (D) is selected, the brushes, squeegee and side brooms (cylindrical models) are automatically lowered to the floor. The scrub, solution, vacuum, detergent (EcoFlex models) and side broom (cylindrical models) systems all start when the Drive Pedal (8) is activated. [. . . ] Adjusting the Squeegee Angle Adjust the squeegee angle whenever a blade is reversed or replaced, or if the squeegee is not wiping the floor dry. 2 Lower the squeegee, move the machine ahead slightly and adjust the squeegee tilt and height using the Squeegee Tilt Adjust Knob (22) and Squeegee Height Adjust Knobs (28) so that the rear squeegee blade touches the floor evenly across its entire width and is bent over slightly as shown in the squeegee cross section. FIGURE 10 A-18 - FORM NO. 56091001 - BR 1100S SBG SPECIAL ENGLISH / A-19 SIDE SKIRT MAINTENANCE The side skirt's function is to channel the waste water to the squeegee, helping contain the water within the machines cleaning path. The operator will notice a small amount of water leaking out underneath the side skirts. [. . . ]