User manual NILFISK BA 511D

[. . . ] The undersigned certify that the above mentioned model is produced in accordance with the following directives and standards. BA 551 BA 551D BA 611D BA 551CD 1 brosse / plateau 1 brosse / plateau 2 brosses / 2 brosses cylindrisupport disque, support disque, plateaux support ques, avec syssans système de avec système de disque, avec système de traction traction traction tème de traction 1 088 mm 58 litres 60 litres 250 mm 1, 2 N/mm2 - 4, 6 N/mm2 100 mm 330 W -- -- 2% 65, 8 dB(A) ± 3 dB(A) 84 dB(A) < 2, 5 m/s2 GEL : (2 x 12 V) 24 V 110 Ah / 5 h 350 x 350 x 300 mm 1. BA 551 BA 551D 1 brosse / plateau 1 brosse / plateau support disque, support disque, sans système de avec système de traction traction 530 mm 760 mm 1 323 mm 541 mm 530 mm 88 kg 236 kg 480 W 153 tr/mn 20, 5 kg 27, 8 kg 102 kg 250 kg 350 W 230 tr/mn 530 mm BA 611D 2 brosses / plateaux support disque, avec système de traction 610 mm 810 mm 1 311 mm 646 mm 305 mm Largeur de nettoyage Largeur embouchure Longueur maximum machine Largeur machine sans embouchure Diamètre brosse Poids sans batteries et avec réservoirs vides Poids maximum avec batteries et réservoir plein Puissance moteur brosse Vitesse de rotation brosses Pression brosse / plateau support disque avec extra-pression désactivée Pression brosse / plateau support disque avec extra-pression activée BAT C1 C2 CH CSC EB1 EB2 ES1 ES2 EV1 F1 F2 F3 F4 F5 F6 HM K1 M1 M2 M3 M4 M5 RV1 RV2 SW1 Batterie 24 V Connecteur batteries Connecteur chargeur de batterie Chargeur de batterie (optionnel) Connecteur secondaire tête porte-brosses cylindriques Carte électronique de fonctions Carte électronique système de traction Télérupteurs moteurs brosses Relais système d'aspiration Electrovanne détergent (optionnelle) Fusible tête Fusible système d'aspiration Fusible système de traction Fusible circuits de signaux Fusible déclenchement brosses / plateaux support disque Fusible pompes Compteur horaire (optionnel) Clé de contact Moteur brosse / plateau support disque Moteur système d'aspiration Moteur système de traction Pompe eau (optionnelle) Pompe détergent (optionnelle) Potentiomètre vitesse Potentiomètre vitesse maximum Microinterrupteur de validation brosses / système de traction Pour accrocher les brosses / plateaux support disque, il suffit d'appuyer sur le panneau (3) en exerçant une légère pression qui actionne seulement les moteurs des brosses / plateaux support disque. Pour déposer les brosses / plateaux support disque, il est nécessaire de soulever la tête en appuyant sur la pédale (11), puis appuyer sur le bouton-poussoir (75) (si présent) et attendre jusqu'à ce que la brosse / plateau support disque tombe au sol. [. . . ] Slightly press the paddle (3) forward to engage the brushes/pad-holders, then release it. If necessary, repeat the procedure until the brushes/pad-holders are engaged. (Only for BA 551D, BA 551CD, BA 611D): Do not press the paddle (3) completely, otherwise the machine will start moving. A slight pressure on the paddle (3) is enough to engage the brushes/pad-holders and to turn on the relevant motors. To remove the brushes/pad-holders, the deck must be lifted by pressing the pedal (11), then press the switch (75) (if equipped) and wait for the brush/pad-holder to fall on the floor. If the machine is not equipped with the automatic release system (switch 75), manually remove the brush/pad-holder from the hub, by turning it in the opposite direction to the normal rotation direction. Install the squeegee (25) and fasten it with the handwheels (26), then connect the vacuum hose (15) to the squeegee. With the handwheel (27), adjust the squeegee so that the rear blade - in all its length - touches the floor and the front blade is slightly detached from the floor. Deck model Deck with one brush (18a), brush diameter: 530 mm Deck with two brushes (18b), brush diameter: 305 mm Deck with two cylindrical brushes (18c), brush length: 485 mm Squeegee model Aluminium (Fig. NOTE If the machine is equipped with EcoFlexTM system (optional) (switches (83 and 77) activated) pour clean water in the tank, otherwise pour solution. (For machine without EcoFlexTM system) Fill the tank (20) with a solution suitable for the work to be performed. Do not fill the solution tank completely, leave a few centimetres from the edge. Always follow the dilution instructions on the label of the chemical product used to prepare the solution. (For machine with EcoFlexTM system) Fill the tank (20) with clean water. Do not fill the clean water tank completely, leave a few centimetres from the edge. Open the cover (22) and check that the recovery tank (21) is empty, otherwise empty it with the drain hose (16). Fill the tank (45) with a detergent suitable for the work to be performed (highly concentrated detergent). Do not fill the detergent tank completely, leave a few inches from the edge. NOTE If the detergent hose (48) is empty (in case of new system, system emptied for cleaning, etc. ), in order to fill the hose quickly, it may be useful to drain EcoFlexTM system once or several times (see the procedure in Maintenance chapter). Check that the green warning light (81a) turns on (charged batteries). If the yellow or red warning light (81b or 81c) turns on, turn the ignition switch back to "0" and charge the batteries (see the procedure in Maintenance chapter). [. . . ] Remove the screws (A) and carefully move aside the panel (B) by disengaging the grommet (K) from its housing on the panel (B). Check/replace the following fuses: C) Brush deck fuse F1: (40 A) D) Vacuum system fuse F2: (30 A) E) Drive system fuse F3: (30 A) (*) F) Signal circuits fuse F4: (3 A) G) Brush/pad-holder release fuse F5: (20 A) (*) H) Pump fuse F6: (3 A) (*) (*) 6. The machine can be equipped with either the brush/pad-holder deck (18a and 18b) or the cylindrical brush deck (18c). NOTE When the deck is installed/removed, it may be necessary to change the squeegee too, because they must have the same width. [. . . ]