User manual NEW POL XR2000EL

[. . . ] 2 PREPARATION 13 13 14 15 15 16 17 17 18 Checking the Contents Removing the Packaging Checking the Components Parts Front Buttons Rear View Side View Adjusting the Product Tilt Adjusting the Product Height 23 23 24 24 27 27 Chapter. 4 USING MHL 28 28 29 MHL (Mobile High-Definition Link) Using MHL Disabling MHL 2 Chapter. 5 CONNECTING AND USING A SOURCE DEVICE 30 30 30 31 31 33 34 34 36 Checklist before Connecting to Source Devices Pre-connection Checkpoints Connecting the Power Connecting and Using a PC Connecting to a PC Driver Installation Setting Optimum Resolution Changing the Resolution Using a PC Connecting to a Video Device Chapter. 7 CONFIGURING THE TINT SETTINGS 40 40 41 41 41 41 42 42 42 42 43 43 Color Mode Configuring Color Mode Red Configuring Red Green Configuring Green Blue Configuring Blue Color Temp. [. . . ] •    On some mobile devices, the MHL function may not be available depending on the device performance or functionality. •    Since the display size of the product is larger than those of mobile devices, the picture quality may degrade. •    This product is officially MHL-certified. In the event of a problem with a mobile device connection, contact the mobile device manufacturer. •    The picture quality may degrade when content (imported from the mobile device) with a low resolution is displayed on the product. 2. Connect the DC power adapter to the product and a power socket. 3. After the power is connected, the product will automatically detect and change the input source. ] button to change the input * If the screen is blank in HDMI/MHL mode, power the product off and then on again. NOTE Mobile devices should be purchased separately. 28 Using MHL 4. If the following message appears, MHL mode is activated. After about 3 seconds, the MHL screen will be displayed. HDMI/MHL MHL MHL Disabling MHL When the cable is disconnected or the mobile device is powered off If the HDMI-MHL cable is disconnected or the mobile device is powered off when MHL is active, the MHL function will be disabled. [MHL] MHL activated. 3 sec later NOTE NOTE The indicated time “after 3 seconds” may vary depending on the mobile device. If the mobile cable is disconnected, HDMI/MHL mode will still be enabled. When the mobile device is in power-saving mode If the mobile device is in power-saving mode, deactivate the power-saving mode. The MHL screen will appear normally. When the mobile device is not connected or does not support MHL If MHL mode does not activate, check the connection of the mobile device. If MHL mode does not activate, check if the mobile device supports MHL. The HUB feature on the product will improve your work efficiency by allowing you to connect multiple source devices to the USB ports on the product at the same time without connecting them to a PC. • If source devices are connected to the PC, the numerous cables around the PC can get tangled and look messy. Connecting them directly to the product will resolve this. 1. Insert the user manual CD provided with the product into the CD-ROM drive. 2. Click "Windows Driver. " 3. Follow the instructions given on the screen to proceed with installation. 4. Select your product model from the list of models. (PC IN) USB 5. Go to Display Properties and check that the resolution and refresh rate are appropriate. Refer to your Windows OS manual for further details. USB USB NOTE •    An external mass-storage HDD requires external power supply. Be sure to connect it to a power source. 33 Connecting and Using a Source Device Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase. Select a language and change the resolution to the optimum value. Changing the Resolution Using a PC NOTE Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP The optimal resolution for this monitor is as follows: Go to Control Panel → Display → Settings and change the resolution. 2560 x 1440 60Hz Follow the above settings to set the resolution. English Exit Move Enter 1. Press [ ], [ ] to move to the language you want and press [ ]. 2. To hide the information message, press [m]. NOTE • If the optimal resolution is not selected, the message will appear up to three times for a specified time even after the product is turned off and on again. • The resolution can also be changed to the optimal setting (1920 x 1080) using Control Panel on your PC. 34 Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel → Personalization → Display Settings and change the resolution. Changing the Resolution on Windows 7 Go to Control Panel → Display → Screen Resolution and change the resolution. 35 Connecting and Using a Source Device Connecting to a Video Device The product can be connected to a video device. [. . . ] charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. [. . . ]