User manual NETGEAR WNDAP330

[. . . ] NETGEAR WNDAP330 ProSafe 802. 11n Dual Band Wireless Access Point Reference Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10361-01 May 2008 v1. 0 © 2008 by NETGEAR, Inc. All rights reserved. . Technical Support Please refer to the support information card that shipped with your product. By registering your product at http://www. netgear. com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades. [. . . ] For WPA, record the following settings for the primary and secondary RADIUS servers: Server Name/IP Address: Primary _________________ Secondary __________________ Port: ___________________________________ Shared Secret: ___________________________________ Use the procedures described in the following sections to configure the WNDAP330. Store this information in a safe place. Basic Installation and Configuration v1. 0, May 2008 2-29 ProSafe Dual Band Wireless Access Point WNDAP330 Reference Manual Configuring the RADIUS Server Settings You can setup or modify the RADIUS Server settings to compliment Network Authentication security options. The RADIUS Server must be used with Legacy 802. 1x, and can be used with WPA and WPA2 Network Authentication. When using a RADIUS Server, the RADIUS Server settings must be configured before completing the Network Authentication security profile (see "Configuring WPA with RADIUS" on page 2-36, "Configuring WPA2 with RADIUS" on page 2-37, or "Configuring WPA and WPA2 with RADIUS" on page 2-38 for specifics on implementing these security options). From your Web browser, log in to the WNDAP330 using the default LAN address of http://192. 168. 0. 235, user name admin and password password, or use the LAN address and password that you set up. Under the Configuration tab, select Security on the main menu, select Advanced from the lefthand menu, and then select RADIUS Server Settings. The RADIUS Server Settings screen will display, as shown in Figure 2-14. 2-30 v1. 0, May 2008 Basic Installation and Configuration ProSafe Dual Band Wireless Access Point WNDAP330 Reference Manual Figure 2-14 3. Enter the following RADIUS Server settings: · Authentication Server. This configuration is required for authentication using a RADIUS Server. The IP Address, Port Number, and Shared Secret are required for communication with the Primary RADIUS Server. You can also configure a Secondary RADIUS Server to use, if the Primary RADIUS Server fails. This is shared between the Wireless Access Point and the RADIUS Server while authenticating the supplicant (wireless client). Accounting Server. The IP Address, Port Number, and Shared Secret are required for communication with the Primary RADIUS Server. You can also configure a Secondary RADIUS Server to use if the Primary RADIUS Server fails. The default is 0. 0. 0. 0 2-31 v1. 0, May 2008 Basic Installation and Configuration ProSafe Dual Band Wireless Access Point WNDAP330 Reference Manual ­ ­ Port Number. This is shared between the Wireless Access Point and the RADIUS Server while authenticating the supplicant (wireless client). 4. Click Apply to save your settings. Setting up a Security Profile The WNDAP330 allows you to set up eight different security profiles for 802. 11b/g/n and eight different profiles for 802. 11a/n. Each profile can be configured with a different security option for network authentication. Note: If you are using a RADIUS Server, configure the RADIUS settings first, as described in the "Configuring the RADIUS Server Settings" on page 2-30. . Figure 2-15 2-32 v1. 0, May 2008 Basic Installation and Configuration ProSafe Dual Band Wireless Access Point WNDAP330 Reference Manual To configure a Security Profile: 1. From your Web browser, log in to the WNDAP330 using the default LAN address of http://192. 168. 0. 230, user name admin and password password, or use the LAN address and password that you set up. Under the Configuration tab, select Security from the main menu, and then select either Security Profile Settings for 802. 11b/g/n or 802. 11a/n. The screen for the Profile Settings you selected will display as shown in Figure 2-16 above. Check the radio button of the profile you want to modify and click Edit. [. . . ] When pressed and released quickly, the WNDAP330 will reboot (restart). This button can also be used to clear ALL data and restore ALL settings to the factory default values. To clear all data and restore the factory default values: 1. Use something with a small point, such as a pen, to press the Reset button in and hold it in for at least 5 seconds. The factory default configuration has now been restored, and the WNDAP330 is ready for use. 5-4 v1. 0, May 2008 Troubleshooting and Debugging Appendix A Default Settings and Technical Specifications This appendix provides the factory default settings and technical specifications for the ProSafe 802. 11n Dual Band Wireless Access Point WNDAP330. Factory Default Settings You can use the reset button located on the front of your device to reset all settings to their factory defaults. [. . . ]