User manual NETGEAR WNAP210

[. . . ] No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc. To register your product, get the latest product updates, or get support online, visit us at http://support. Trademarks NETGEAR, the NETGEAR logo, ReadyNAS, ProSafe, Smart Wizard, Auto Uplink, X-RAID2, and NeoTV are trademarks or registered trademarks of NETGEAR, Inc. microsoft , Windows , Windows NT , and Vista are registered trademarks of Microsoft Corporation. [. . . ] Your browser extracts the configuration file (the file name is config) from the wireless access point and prompts you for a location on your computer to store the file. Restore the Configuration IMPORTANT: During the restoration process, do not try to go online, turn off the wireless access point, shut down the computer, or do anything else to the wireless access point until it finishes restarting!During the restoration process, the wireless access point automatically restarts. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point. Management | 61 ProSafe Wireless-N Access Point WNAP320 Reference Manual Restore the Wireless Access Point to the Factory Default Settings You can restore the wireless access point to the factory default settings by two methods that are described in the following sections: • • Use the Web Management Interface to Restore Factory Default Settings on this page Use the Reset Button to Restore Factory Default Settings on page 63 Note: After you have restored the factory default settings on the wireless access point: * All custom configurations will be lost. * The Access Point Name field will be reset to the name printed on the label on the bottom of the unit. Use the Web Management Interface to Restore Factory Default Settings IMPORTANT: During the restoration process, do not try to go online, turn off the wireless access point, shut down the computer, or do anything else to the wireless access point until it finishes restarting!To restore the factory default settings using the Web Management Interface: 1. Click Apply to reset the wireless access point to the factory default settings. During the restoration process, the wireless access point automatically restarts. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point. Use the Reset Button to Restore Factory Default Settings To restore the factory default settings when you do not know the login user name, login password, or IP address, you must use the Reset button on the rear panel of the wireless access point (see Figure 2 on page 12). Using a sharp object, press and hold the Reset button for about 5 seconds (until the Test LED blinks rapidly) to reset the wireless access point to factory defaults settings. Note: Pressing the Reset button for a shorter period of time simply causes the wireless access point to reboot. During the restoration process, the wireless access point automatically restarts. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point. Reboot the Wireless Access Point without Restoring the Default Configuration If you do not have physical access to the wireless access point to switch it off and on again, you can use the software to reboot the wireless access point. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point. The ideal password should contain no dictionary words from any language, and should be a mixture of letters (both uppercase and lowercase), numbers, and symbols. Take one of the following actions: • Enter a new password twice: once in the New Password field and again in the Repeat New Password field. € Next to Restore Default Password, select the Yes radio button to restore the default password. If you have restored the default password, the login password will be password. [. . . ] Canadian Department of Communications Radio Interference Regulations This digital apparatus, ProSafe Wireless-N Access Point WNAP320, does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. [. . . ]