User manual NETGEAR SB104 INSTALLATION GUIDE

[. . . ] Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer It is hereby certified that the Model FA311 PCI Adapter and the Model EN104TP Ethernet Hub have been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. [. . . ] · Places the hub and PCs close enough to connect the network cables. To install the hub on a wall, measure the distance between the mounting holes at the back of the hub and mark the wall to match the location of the mounting holes. Drill pilot holes at the two marked locations on the wall and screw two 5/16-inch diameter flathead screws (provided) into the wall so that the screws protrude 1/18 inch to 3/16 inch. If the Pwr LED is not on, the hub is defective and should be returned to your point-of-sale representative. The push button is set to Uplink only if the port 4 is connected to another hub for expansion purposes. Link LED Rx LED Category 5 10/100 Mbps UTP cables* *Use the cables provided or any Categor y 5 UTP cable . Maximum length = 100 meters (300 feet) 7995FB RJ-45 connector RJ-45 connector port on a network card in each PC. Note: The Model FA311 PCI Adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. EN 55 022 Statement (for the Model EN104TP Ethernet Hub) This is to certify that the Model EN104TP Ethernet Hub is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class A (CISPR 22). Go to http://www. NETGEAR. com for the NETGEAR Web page. Defective or damaged merchandise can be returned to your point-of-sale representative. To get product support, or to obtain product information and NETGEAR product documentation, direct your Web browser to the http://www. NETGEAR. com Web page. To register online, direct your Web browser to the http://www. gearguy. com/pub/registration Web page. If you do not have access to the World Wide Web, you can complete the enclosed registration card and mail it to NETGEAR customer service. Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, Pwr LED in which case the user may be required to take appropriate measures. EN 55 022 Statement (for the Model FA311 PCI Adapter) Col LED RJ-45 ports Normal/Uplink push button (Normal position when connected to a PC) This is to certify that the Model FA311 PCI Adapter is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22). Ground clip (not used) Power adapter receptacle 7979FB *M1-SB104NA-6* * M 1 S B 1 0 4 N A 6 * August 2000 SB104. QCard. R2 9/7/00 4:53 PM Page 2 INSTALL THE WINDOWS 98 DRIVERS This guide provides instructions for installing the Windows 98 network driver. Since all versions of Windows may not respond similarly, your computer screen may display different information, in a different order, than pictured in the following instructions. Note: You must install the network card (instructions on the other side of this guide) before installing the network driver. [. . . ] Select "Floppy disk drives" and insert the NETGEAR FA311 Fast Ethernet PCI Adapter Drivers and Diagnostics disk into the floppy drive. In the "Update Device Driver Wizard" dialog box, click on "Finish. " 12. Remove the NETGEAR FA311 Drivers and Diagnostics disk and the Windows 98 CD-ROM. When asked if you want to restart your computer, click on "Yes. " You must restart your computer to complete the installation of the driver. 3W +5V +/- 5% @ 630 mA maximum 7. 5 W 7. 5 V @ 1 A maximum 5. 7 by 3. 7 in. [. . . ]