User manual NETGEAR GS504 Installation Guide

[. . . ] · · · Wire-speed filtering and forwarding of the traffic with no delay Store-and-forward intelligent processing to minimize erroneous packets on the network Easy plug-and-play installation with no software to configure, which saves time and minimizes the potential for configuration errors Model GS504 4-Port Gigabit Switch Installation Guide Protocol independence and compatibility with all major protocols such as TCP/IP, NetWare, DECnet, and Microsoft Networks Package Contents Model GS504 Switch Ethernet MODEL GS504SX 4PORT 10/100Mbps Gigabit Fiber Switch Tx Activity Power 1 2 3 4 1 Rx Link Tx 2 Rx Link Tx 3 Rx Link Tx 4 Rx Link Green=FDX, Yellow=Col Rubber footpads AC power cord Rack mount kit Installation guide, Warranty & Owner Registration Card, Support Information Card 9328FA Verify that your package contains the following: · · · · · · · Model GS504 switch Rubber footpads for tabletop installation This installation guide Rack mount kit for 19-inch rack installation Warranty & Owner Registration Card Support Information Card Power cord Model GS504 4-Port Gigabit Switch Installation Guide Product Illustration Front Panel The front panel of the Model GS504 switch contains the following LEDs that correspond to each network port: Activity (Rx/Tx) and FDX (full-duplex)/ Collision. Each fiber network port has its own Link LED (located to the right of each 1000 Mbps port). Front Panel of the Model GS504 Switch Activity LEDs Fiber network ports Ethernet MODEL GS504SX 4PORT 10/100Mbps Gigabit Fiber Switch Tx Activity Power 1 2 3 4 1 Rx Link Tx 2 Rx Link Tx 3 Rx Link Tx 4 Rx Link Green=FDX, Yellow=Col FDX/Collision LED Power LED Link LED 9318FA LEDs The table below describes the activity of the LEDs. Label Power FDX/Col Color Green Green Activity On Off On Off Blinking Description Power is supplied to the switch. A link is not established on the port. Yellow Activity Link Green Green Blinking On Off Model GS504 4-Port Gigabit Switch Installation Guide Rear Panel The rear panel of the Model GS504 switch has fans for cooling and a standard AC power receptacle for the supplied power cord. Rear Panel of the Model GS504 Switch Fans AC power outlet 100-240 VAC 50-60 Hz 9320FA Applications Desktop Switching The Model GS504 switch is used as a desktop switch to build a powerful network that enables users to have 1000 Mbps access to a file server. [. . . ] In other words, the transmit port of one interface must be wired to the receive port of the opposite interface and vice versa. Fiber cables must be connected in this manner to transmit and receive data. Tx Rx 8895FA Verify Installation When power has been applied to the switch, verify that: · · The green Pwr LED on the front panel is on. The green Link LED on each connected port is on. When the switch is connected and operating, refer to the table in "LEDs" for information about the LEDs and their activity. Model GS504 4-Port Gigabit Switch Installation Guide Troubleshooting Information Symptom Cause Solution Power LED is off. No power is received Check the power cord connections for the at the hub. Make sure all cables used are correct and comply with Ethernet specifications. Check the crimp on the fiber connectors and make sure that the plug is properly inserted and locked into the port at both the switch and the connecting device. Make sure all cables used are correct and comply with Ethernet specifications. Check for a defective adapter card, cable, or port by testing them in an alternate environment where all products are functioning. Make sure the remote link partner is set to autonegotiate or forced to full-duplex operation. File transfer is slow or performance degradation is a problem. FDX/Col LED is blinking yellow excessively. Half- or full-duplex setting on the NETGEAR switch and the connected device are not the same. One or more devices are not properly connected, or cabling does not meet Ethernet guidelines. Verify that the cabling is correct. Be sure all cable connectors are securely positioned in the required ports. Equipment may have been accidentally disconnected. Collisions are Some collisions are normal when the occurring on the connection is operating in half-duplex mode. Recheck the link partner settings. Model GS504 4-Port Gigabit Switch Installation Guide Technical Specifications General Specifications Network Protocol and Standards Compatibility Data Rate Interface Power Consumption Input Voltage (Power Adapter) Physical Specifications Dimensions: Weight: Environmental Specifications Operating temperature: Operating humidity: Electromagnetic Compliance 0° to 40° C (32° to 104° F) 90% maximum relative humidity, noncondensing CE mark, commercial FCC Part 15 Class A VCCI Class A EN 55022 (CISPR 22) Class A, EN50082-1 C-Tick Safety Agency Approvals UL Listed (UL 1950), cUL TUV Licensed (EN 60 950), IEC 95 Performance Specifications Frame filter rate: Frame forward rate: Network latency (using 64-byte packets): Address database size: Addressing: Queue buffer: 1, 480, 000 frames/second maximum 1, 480, 000 frames/second maximum 30 microseconds maximum 8, 000 media access control (MAC) addresses 48-bit MAC address 2 MB memory per port 13. 0 x 1. 7 x 8. 0 in. [. . . ] Voluntary Control Council for Interference (VCCI) Statement This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in commercial and/or industrial areas. Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio interference may be caused to equipment such as radios and TV receivers. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This device complies with part 15 of the FCC Rules. [. . . ]