User manual NETGEAR FSM7326P

[. . . ] Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Software Version 4. 0 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA Beta Draft 1 March 2006 © 2006 by NETGEAR, Inc. FullManual. Trademarks NETGEAR and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. . Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. [. . . ] The interface is a logical slot and port for a configured port-channel. The option all sets every configured port-channel with the same administrative mode setting. Format Mode no port-channel linktrap {<logical unit/slot/port> | all} Global Config Port-Channel/LAG (802. 3ad) Commands v1. 0, March 2006 12-5 Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12. 2 Port-Channel Show Commands This section describes the commands you use to view port-channel status and configuration information. 12. 2. 1 show port-channel brief This command displays the static capability of all port-channels (LAGs) on the device as well as a summary of individual port-channels. Format Modes Static Capability show port-channel brief Privileged EXEC User EXEC This field displays whether or not the device has static capability enabled. This field lists the ports that are members of this port-channel, in <unit/slot/port> notation. This field lists the ports that are actively participating in this port-channel. For each port-channel the following information is displayed: Name Link State Mbr Ports Active Ports 12. 2. 2 show port-channel This command displays an overview of all port-channels (LAGs) on the switch. Format Modes Logical Interface Port-Channel Name Link State Admin Mode show port-channel {<logical unit/slot/port> | all} Privileged EXEC User EXEC Valid slot and port number separated by forward slashes. The factory default is enabled. 12-6 Port-Channel/LAG (802. 3ad) Commands v1. 0, March 2006 Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, Link Trap Mode STP Mode This object determines whether or not to send a trap when link status changes. The Spanning Tree Protocol Administrative Mode associated with the port or port-channel (LAG). The possible values are: Disable - Spanning tree is disabled for this port. A listing of the ports that are members of this port-channel (LAG), in unit/slot/port notation. There can be a maximum of eight ports assigned to a given port-channel (LAG). This field displays the status designating whether a particular port-channel (LAG) is statically or dynamically maintained. This field lists ports that are actively participating in the portchannel (LAG). Mbr Ports Port Speed Type Active Ports Port-Channel/LAG (802. 3ad) Commands v1. 0, March 2006 12-7 Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 12-8 Port-Channel/LAG (802. 3ad) Commands v1. 0, March 2006 Chapter 13 Quality of Service (QoS) Commands This section describes the Quality of Service (QoS) commands available in the 7300S Series Stackable Switch CLI. This section contains the following topics: · · · · · · · · Section 13. 1 "Class of Service (CoS) Commands" on page 13-1 Section 13. 2 "Differentiated Services (DiffServ) Commands" on page 13-8 Section 13. 3 "DiffServ Class Commands" on page 13-10 Section 13. 4 "DiffServ Policy Commands" on page 13-16 Section 13. 5 "DiffServ Service Commands" on page 13-21 Section 13. 6 "DiffServ Show Commands" on page 13-22 Section 13. 7 "MAC Access Control List (ACL) Commands" on page 13-29 Section 13. 8 "IP Access Control List (ACL) Commands" on page 13-33 The commands in this section are in one of two functional groups: · Configuration Commands are used to configure features and options of the switch. For every configuration command there is a show command that will display the configuration setting. Show commands are used to display device settings, statistics and other information. · 13. 1 Class of Service (CoS) Commands This section describes the commands you use to configure and view Class of Service (CoS) settings for the switch. The commands in this section allow you to control the priority and transmission rate of traffic. Note: Commands you issue in the Interface Config mode only affect a single interface. Commands you issue in the Global Config mode apply to all interfaces. Quality of Service (QoS) Commands v1. 0, March 2006 13-1 Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 13. 1. 1 classofservice dot1p-mapping This command maps an 802. 1p priority to an internal traffic class. The <userpriority> and <trafficclass> values can both range from 0-7, although the actual number of available traffic classes depends on the platform. For more information about 802. 1p priority, see Section 6. 3 "Provisioning (IEEE 802. 1p) Commands" on page 6-14. [. . . ] Shows the text of the trap message. 18. 4 CLI Command Logging Command This section describes the commands you use to configure CLI Command Logging. 18. 4. 1 logging cli-command This command enables the CLI command logging feature, which enables the 7300S Series Stackable Switch software to log all CLI commands issued on the system. Default Format Mode enabled logging cli-command Global Config 18. 4. 1. 1 no logging cli-command This command disables the CLI command Logging feature. Format Mode no logging cli-command Global Config System Maintenance Commands v1. 0, March 2006 18-27 Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, 18. 5 Configuration Scripting Commands Configuration Scripting allows you to generate text-formatted script files representing the current configuration of a system. You can upload these configuration script files to a PC or UNIX system and edit them. [. . . ]