User manual NETGEAR FS752TS HW INSTALLATION GUIDE

[. . . ] Hardware Installation Guide for the Prosafe Stackable Smart Switch FS700TS Series NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA Phone 1-888-NETGEAR 202-10150-01 December 2005 © 2005 by NETGEAR, Inc. NETGEAR, the Netgear logo, Prosafe, The Gear Guy and Everybody's connecting are trademarks of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. [. . . ] 2 Gigabit Interface Converter SFP slots for SFP modules (ports 49F and 50F) 13. 4 RJ-45 connectors for 10BASE-T, 100BASE-TX and 1000BASE-T (ports 49T, 50T, 51, and 52) 14. Factory Defaults button Introduction v1. 0, December 2005 2-9 Hardware Installation Guide for the Prosafe Stackable Smart Switch FS700TS Series LED Designations Port LEDs The following table describes the port LED designations. PORT LEDs on Non-PoE Devices Port 24/48 10/100M Ports--One LED/Port LED Link/ACT/SPD LED Designation Off : No 10/100Mbps link is established on the port. Flashing Green: Packet transmission or reception is occurring on the port at 100Mbps. Flashing Yellow: Packet transmission or reception is occurring on the port at 10Mbps. Flashing Green: Packet transmission or reception is occurring on the port at 1000Mbps. Flashing Yellow: Packet transmission or reception is occurring on the port at 10/100Mbps. Off: Stack port does not have a valid link connection. 4 Gigabit Copper Ports-- Two LED's/Port on Jack Left LED Link/ACT/ SPD LED: Right LED Stack LED (Combo port group/Copper port group): 2 SFP Ports--One LED/Port SFP Link/ACT LED Off: No link is established on the port. Flashing Green: Packet transmission or reception is occurring on the port. 2-10 v1. 0, December 2005 Introduction Hardware Installation Guide for the Prosafe Stackable Smart Switch FS700TS Series Table 2-2. Port LEDS on PoE Devices Port 48 10/100M Ports--One LED/Port (Ethernet Mode) LED Link/ACT/SPD LED Designation Off: No 10/100Mbps link is established on the port. Flashing Green: Packet transmission or reception is occurring on the port at 100Mbps. Flashing Yellow: Packet transmission or reception is occurring on the port at 10Mbps. Solid Green: The PoE powered device (PD) is connected and the port is supplying power successfully. Solid Yellow: Indicates one of the following failures resulted in stopping power to that port: · Short circuit on PoE power circuit · PoE power demand exceeds power available · PoE current exceeds PD's classification · Out of proper voltage band (44 ~ 57 VDC) Off: No PoE powered device (PD) connected. Note: PoE mode is only available on the leftmost 24 of the 10/100M ports (ports 1-24). 4 Gigabit Copper Ports-- Two LED's/Port on Jack Left LED Link/ACT/ SPD LED: Off: No 10/100/1000Mbps link is established on the port. Flashing Green: Packet transmission or reception is occurring on the port at 1000Mbps. Flashing Yellow: Packet transmission or reception is occurring on the port at 10/100Mbps. Flashing Green: Packet transmission or reception is occurring on the port. 24 10/100M Ports--One LED/Port (PoE Mode) POE Indicate LED/ POE fault 2 SFP Ports--One LED/Port SFP Link/ACT LED Introduction v1. 0, December 2005 2-11 Hardware Installation Guide for the Prosafe Stackable Smart Switch FS700TS Series System LEDs The following table describes the system LED designations. Table 2-3. System LEDs LED Port 1-24 Mode LED Stack ID LED--One 7-segment LED Display Stack Master LED Designation Solid Green: Ethernet LED Mode (default) Solid Yellow: PoE LED Mode Green: Displays Stack ID (1-6). The Stack Master LED is lit if there is an active stack link, and the unit is in stack mode. [. . . ] If the Power LED does not go on, check that the power cable is plugged in correctly and that the power source is good. If this does not resolve the problem, see Chapter 4, "Troubleshooting". Step 8: Switch Management through a Web Browser or the PC Utility for Initial Configuration The NETGEAR Smart Switch contains software for viewing, changing, and monitoring the way it works. However, the management software enables the setup of VLAN and Trunking features, and also improves the efficiency of the switch, which results in the improvement of its overall performance as well as the performance of the network. After powering up the switch for the first time, the Smart Switch can be configured using a Web browser or a utility program called Smart Wizard Discovery. [. . . ]