User manual NETGEAR FS605 Installation Guide

[. . . ] E-mail: support@NETGEAR. com (24 x 7 online support) www. NETGEAR. com Fast Ethernet Switch 10/100 Mbps FS605 v2/FS608 v2 © 2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Fast Ethernet Switch FS605 v2/FS608 v2 You use the FS605 v2/FS608 v2 switch to build a small network that enables you to have 10 Mbps or 100 Mbps access to other devices on the network. Also, with this switch, you can add extra computers to your cable or DSL router. Unlike a hub that shares its connection with all devices, the FS605 v2/FS608 v2 switch provides a full, dedicated 100 Mbps (or 10 Mbps) connection between two devices. If a device has full-duplex capability, the FS605 v2/FS608 v2 switch provides a 200 Mbps (or 20 Mbps) connection. Ethernet cables come as either straight-through or crossover cables--depending on whether you're connecting to a device (computer, server, or printer) or networking equipment (hub, switch, or router). With the Auto UplinkTM feature, you don't have to worry about which one you use. Each port on the FS605 v2/FS608 v2 switch automatically configures itself correctly when you plug in a device's cable. If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7 days a week on the Web (www. NETGEAR. com), by e-mail (support@NETGEAR. com) and by phone (see the provided support information card for phone numbers). EN 55 022 Declaration of Conformance This is to certify that the NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22). Canadian Department of Communications Radio Interference Regulations This digital apparatus (NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Règlement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (NETGEAR Model FS605 v2/FS608 v2 Fast Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. Installation Overview Estimated Time: 5­10 minutes 1. Install the switch and connect the other devices. 1 Unpack the Box and Verify the Contents Fast Ethernet Switch FS605 v2/FS608 v2 2 · · · Prepare to Install the Switch Decide where you want to place the switch. You're welcome to use the screws if you want to hang the switch in an open space on a wall. Use the vertical stand if you cannot provide adequate clear space on all sides with the switch in a horizontal position. Make sure the selected location is: Not in direct sunlight or near a heater or heating vent. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. [. . . ] · Make sure the cable connectors are securely plugged in at the switch and the device. If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card or adapter is installed correctly and is working. Make sure the cable is less than 328 feet (100 meters). Fast Ethernet Switch FS605 v2 · Fast Ethernet Switch FS608 v2 Technical Specifications Standards Compatibility: Data Rate: Network Interface: DC Power: Physical Dimensions: Weight: Operating Temperature: Operating Humidity: Electromagnetic Compliance: Safety Agency Approvals for the Power Adapter: IEEE 802. 3i 10BASE-T Ethernet, IEEE 802. 3u, 100BASE-TX Fast Ethernet IEEE 802. 3x Flow Control; compatible with Windows®, Mac® OS, NetWare®, Linux® 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX 10 or 100 Mbps half-duplex RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface 7. 5 W max and 7. 5 V @ 0. 8A DC input FS605 v2 - W: 116. 37 mm (4. 58") D: 89. 75 mm (3. 53") H: 34. 42 mm (1. 36") FS608 v2 - W: 158. 37 mm (6. 24") D: 89. 75 mm (3. 53") H: 34. 42 mm (1. 36") FS605 v2 - 0. 13 kg (0. 287 lbs); FS608 v2 - 0. 18 kg (0. 397lbs) 0 to 40° C (32 to 104° F) 10% t0 90% relative humidity, non-condensing CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B, VCCI Class B, C-Tick CE mark, Commercial UL listed (UL 1950), TUV licensed (EN 60950), C-Tick 1. [. . . ]