User manual NETGEAR FS108

[. . . ] E-mail: support@NETGEAR. com (24 x 7 online support) www. NETGEAR. com Fast Ethernet Switch 10/100 Mbps FS105 v2/FS108 v2 © 2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. PWR 1 2 3 4 5 6 7 8 Fast Ethernet Switch FS105 v2/FS108 v2 You use the FS105 v2/FS108 v2 switch to build a small network that enables you to have 10 Mbps or 100 Mbps access to other devices on the network. Also, with this switch, you can add extra computers to your cable or DSL router. Unlike a hub that shares its connection with all devices, the FS105 v2/FS108 v2 switch provides a full, dedicated 100 Mbps (or 10 Mbps) connection between two devices. If a device has full-duplex capability, the FS105 v2/FS108 v2 switch provides a 200 Mbps (or 20 Mbps) connection. Ethernet cables come as either straight-through or crossover cables--depending on whether you're connecting to a device (computer, server, or printer) or networking equipment (hub, switch, or router). With the Auto UplinkTM feature, you don't have to worry about which one you use. Each port on the FS105 v2/FS108 v2 switch automatically configures itself correctly when you plug in a device's cable. If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7 days a week on the Web (www. NETGEAR. com), by e-mail (support@NETGEAR. com) and by phone (see the provided support information card for phone numbers). EN 55 022 Declaration of Conformance This is to certify that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22). Canadian Department of Communications Radio Interference Regulations This digital apparatus (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Règlement sur le brouillage radioélectrique du ministère des Communications Cet appareil numérique (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) respecte les limites de bruits radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada. Installation Overview Estimated Time: 5­10 minutes 1. Install the switch and connect the other devices. 1 Unpack the Box and Verify the Contents Fast Ethernet Switch FS105 v2/FS108 v2 Fast Ethe rnet Switch MODEL 2 MODEL Prepare to Install the Switch Decide where you want to place the switch. You're welcome to use the screws if you want to hang the switch in an open space on a wall. Make sure the selected location is: Fast Ethernet Switch FS108 FS105 FAST ETHERN ET SWITCH FS108 · · · Not in direct sunlight or near a heater or heating vent. There should be at least 2 inches (5 cm) of clear space on all sides of the switch. Well ventilated (especially if it is in a closet). Auto 10/100 Mbps 100M 10M On=Link Blink=Act PWR 1 2 3 4 5 6 7 8 Wall-mount hardware Installation guide, warranty/registration card and support information card Also, you'll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device you want to connect to the switch. [. . . ] · · · Make sure the connected device is turned on. If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card or adapter is installed correctly and is working. Make sure the cable is less than 328 feet (100 meters). Technical Specifications 1. [. . . ]