User manual NETGEAR FR114W Reference Guide

[. . . ] Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall Family NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA Phone 1-888-NETGEAR SM-FM114PNA-0 May 2002 © 2002 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR and Auto Uplink are trademarks or registered trademarks of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. [. . . ] If the setup program does not start automatically, run SETUP. EXE in the root folder. Print Server 7-1 Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall 3. 7. Scroll down to the Drivers section and click on FR114P Print Server driver for Windows. When the installation is finished, make sure the `Run Print Port Setup now' checkbox is checked, and click Finish. The Print Port Setup will then run, and the following screen will be displayed: The screen should show your firewall and printer. 8. Click on the Port 1 symbol, and then click the Add button. Note: Under Windows95, you may receive an error message stating that SETUPAPI. DLL was not found. In this case, you should either upgrade your Internet Explorer to version 5 or later, or consult the Print Server Troubleshooting section in this chapter. 9. A pop-up message will inform you if the port has been created successfully, and then the Windows Add Printer wizard will start. a. Select the correct Printer Manufacturer and Model, or use the `Have Disk' option if appropriate. 7-2 Print Server Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall c. d. If desired, change the Printer name to be more descriptive (such as DeskJet on PrintServer) If prompted about Sharing, do NOT enable Sharing. 10. You can now print using this printer. To make changes later, use the Start menu to run this program. The default installation is Start -> Programs -> NETGEAR Firewall Print Server -> Add Port. Printer Management · Using PTP printing, print jobs can be managed in the same manner as any Windows printer. Open the Printers folder (Start -> Settings -> Printers) and double-click any printer to see the current print jobs. If the printer attached to the firewall is changed, run the `Add Port' program again and select the new printer. To delete a port created by this setup program, use the `Windows Delete Port' facility: a. b. · · Right-click any printer in the Printers folder, and select Properties. This button is on either the Details or Ports tab, depending on your version of Windows. Port Options The options for the Print Port Driver are accessed via the Windows Port Settings button. Print Server 7-3 Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall Use Start -> Settings -> Printers to open the Printers folder, then right-click the Printer and select Properties. The Port Settings button is on either the Details or Port tab, depending on your version of Windows. An example screen is shown below: Items shown on this screen are as follows: · Port If desired, click Browse to select a different device. The `Select Device Port' button supports multi-port models, but the firewall is a single-port print server. · Banner Check this option to print a banner page before each print job. · Retry Interval Determines how often Windows will poll the print server to establish a connection when the printer is busy. LPD/LPR Printing from Windows LPD/LPR printing is supported by Windows NT 4. 0 Server and Windows 2000/XP. Third-party drivers are available for earlier versions of Windows. 7-4 Print Server Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall Windows NT 4. 0 Server Configuration To use LPD printing, Microsoft TCP/IP Printing must be installed and enabled. This can be checked using Start-Settings-Control Panel-Network - Services. [. . . ] The portion of a number, address, or field that is farthest left when written as a single number in conventional hexadecimal ordinary notation. Glossary IKE IP IP Address IPSec ISP LAN local area network MAC address Mbps MSB MRU Maximum Receive Unit Most Significant Bit or Most Significant Byte 2 Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall NAT netmask See Network Address Translation. A number that explains which part of an IP address comprises the network address and which part is the host address on that network. It can be expressed in dotted-decimal notation or as a number appended to the IP address. [. . . ]