User manual NETGEAR DGN3500

[. . . ] RangeMax Wireless-N DSL Gigabit Modem Router DGN3500 User Manual NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134 USA 202-10487-01 November 2009 v1. 0 ©2009 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR, the NETGEAR logo, and RangeMax are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks and Vista is a trademark of Microsoft Corporation. [. . . ] Select Schedule below Security to display the Schedule screen that is shown in Figure 3-12. To block Internet services based on a schedule, select Every Day or select one or more days. If you want to limit access completely for the selected days, select All Day. Otherwise, to limit access during certain times for the selected days, or enter times in the Start Time and End Time fields. If you set the start time after the end time, the schedule will be effective through midnight the next day. Click Apply to save your changes. 3-16 v1. 0, November 2009 Protecting Your Network RangeMax Wireless-N DSL Gigabit Modem Router DGN3500 User Manual Configuring E-mail Alerts and Web Access Log Notifications To receive logs and alerts by e-mail, you must provide your e-mail account information. Enter your email details: · Enter the name of your ISP's outgoing (SMTP) mail server (such as mail. myISP. com) in the Your Outgoing Mail Server field. You might be able to find this information in the configuration screen of your e-mail program. If you leave this field blank, log and alert messages will not be sent by e-mail. Protecting Your Network v1. 0, November 2009 3-17 RangeMax Wireless-N DSL Gigabit Modem Router DGN3500 User Manual · Enter the e-mail address to which logs and alerts are sent in the Send To This E-mail Address field. If you leave this field blank, log and alert messages will not be sent by e-mail. If your outgoing e-mail server requires authentication, select the My Mail Server requires authentication check box. ­ ­ Enter your user name for the outgoing e-mail server in the User Name field. Enter your password for the outgoing e-mail server in the Password field. · 4. You can specify that logs are automatically sent by e-mail with these options: · · Send alert immediately. Select this check box for immediate notification of attempted access to a blocked site or service. Specifies how often to send the logs: Hourly, Daily, Weekly, or When Full. Relevant when the log is sent daily or weekly. If you select the Weekly, Daily, or Hourly option and the log fills up before the specified period, the log is automatically e-mailed to the specified e-mail address. After the log is sent, the log is cleared from the router's memory. If the router cannot e-mail the log file, the log buffer might fill up. In this case, the modem router overwrites the log and discards its contents. So that the log entries are correctly time-stamped and sent at the correct time, be sure to set the time as described in the next section. 3-18 v1. 0, November 2009 Protecting Your Network Chapter 4 Managing Your Network This chapter describes features to help you manage your Wireless-N Modem Router. This chapter includes the following sections: · "Upgrading the Firmware · "Viewing Wireless Modem Router Status Information" on page 4-4 · "Viewing a List of Attached Devices" on page 4-8 · "Managing the Configuration File" on page 4-9 · "Running Diagnostic Utilities and Rebooting the Wireless Modem Router" on page 4-10 · "Enabling Remote Management Access" on page 4-11 Note: For help with changing the password, see "How to Change the Built-In Password" on page 3-2. Upgrading the Firmware The modem router's firmware (routing software) is stored in flash memory. [. . . ] If the IP configuration of your PC is assigned by DHCP, this information will not be visible in your PC's Network Control Panel. Verify that the IP address of the router is listed as the default modem router as described in the online document that you can access from "Preparing Your Network" in Appendix B. Check to see that the network address of your PC (the portion of the IP address specified by the netmask) is different from the network address of the remote device. If your ISP assigned a host name to your PC, enter that host name as the account name in the Basic Settings screen. [. . . ]