User manual NETGEAR ANT24O5

[. . . ] 5 dBi Omni-directional Antenna ANT24O5 Installation Guide Introduction This section introduces the package contents of the NETGEAR 5 dBi Omni-directional Antenna ANT24O5 and related components. NOTE: To obtain optimal results in extending wireless range with antenna installations, it is recommended that a qualified professional installer service is consulted for site survey and proper installation. To comply with FCC rules the ANT24O5 antenna should only be used with devices that have been FCC approved for use with the ANT24O5. [. . . ] So, even with 20dB to 40dB of attenuation, the signal strength is still strong and communication is maintained. Approximate coverage area Figure 1: Optimal antenna placement on the ceiling The longer the antenna cable, the higher the attenuation, or signal loss. The best performance is achieved with a short cable between the antenna and the wireless device. The shortest FCC approved antenna cable is the NETGEAR 1. 5 M (ACC-10314-01) cable. For optimal performance, use a low-loss NETGEAR antenna cable up to 10 meters long. If the wireless access point, router or gateway is in a IT room, place the antenna outside of the room close to the ceiling against a wall. Use a NETGEAR antenna cable of up to 10 meters in length to connect the antenna to the wireless access point. 2 3 Installing the Antenna The instructions below cover these scenarios: · · · Wireless device with a single antenna Wireless device with two antennas, but replacing only the primary antenna Wireless device with two antennas, but replacing both the primary and secondary antennas Wireless device with two antennas, but replacing only the primary antenna 5 dBi Antenna ANT24O5 Antenna executes both transmit and receive function. Turn off your wireless unit, locate the scenario below that fits your equipment, and connect your wireless accessories according to the illustration. After attaching your new antenna, reconnect your wireless device to the network and turn it on. Wireless device with a single antenna 5 dBi Antenna ANT24O5 Antenna executes both transmit and receive function. NETGEAR antenna cable Antenna Connection Wireless Access Point ETHERNET RESET 5-12V DC Primary Secondary Wireless device with two antennas, but replacing both the primary and secondary antennas NETGEAR antenna cable ETHERNET RESET 5 dBi Antenna ANT24O5 Antenna executes both transmit and receive function. 5 dBi Antenna ANT24O5 Antenna executes receives function only. 5-12V DC Antenna Connection Wireless Access Point Wireless Access Point ETHERNET RESET NETGEAR antenna cable Antenna Connection 5-12V DC Primary Secondary 4 5 Specifications Description Frequency Range Type Impedance Maximum Input Power SWR Return Loss Gain Radiation Polarization Beam Degree Connector Type Material Color Mounting Base Operation Temperature Storage Temperature Device Size (l x w x h) Weight Warranty The ANT24O5 built-in cable specifications are listed here. ANT24O5, 5 dBi Omni-directional Antenna with a 10cm RG318 cable and reverse female jack SMA connector 2450 ± 50MHz Patch 50 ± 5 Ohms 20W (without N/SMA adapter) 2. 0 maximum -10 dB 5 dBi Directional Vertical HORZ 120 ° VERT 110 ° SMA Female reverse PC+ABS WHITE STEEL -20 to 65° C (-4 to 149° F) -30 to 80° C (-22 to 176° F) 99. 2 x 53. 9 x 27. 5 mm/3. 91 x 21. 2 x 1. 08 in Description Type Length External Diameter Impedance SWR Loss Minimum bend radius 10cm RG318 RG318 10 cm = 3. 9 in 2. 5 mm 50 ± 5 Ohms 1. 5 maximum 138 dB/100 m = 42 dB/100 ft @ 2. 4 GHz 13 mm = 0. 5 in Horizontal Plane Radiation Pattern (X-Y, Azimuth) 90 120 60 150 30 180 -30 0 Top View 210 330 240 300 270 55 g/. 12 lb. 2 years 6 7 Vertical Plane Radiation Pattern (X-Z, Elevation) 90 120 60 Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice 150 30 Front 180 -30 0 Side View 210 330 240 270 300 This device complies with part 15 of the FCC Rules. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. [. . . ]