User manual NETGEAR ANT24D18

[. . . ] Please check the NETGEAR web site at http://www. NETGEAR. com/go/antennas_eu for a list of restrictions and approved devices. Wall Mount Configuration With Adjustable Brackets This illustration shows the wall mount configuration with adjustable brackets. 2 3 Wall Mount Configuration With Fixed Brackets This illustration shows the wall mount configuration with fixed brackets. - More range: Use the 18 dBi one side with short antenna cable. For instance WG302, 1. 5m cable ACC-10314-01, lightning arrestor, 2m cable, and ANT24D18 on one side and WG302 (with own antennas) on the other side. Super range: Use the 18 dBi both side with short/medium antenna cable. For instance WG302, 3m cable ACC-10314-02, lightning arrestor, 2m cable, and ANT24D18 on both sides. [. . . ] 2 ANT24D18s per wireless node (requires both primary and secondary RF ports) can improve the range and throughput by providing spatial diversity. - 4 5 Warning, Indoor point to multipoint: the ANT24D18 is not omnidirectional and is not suitable when low ceilings, partial obstructions, walls, cubicles, large metal objects, etc. WLAN communications can suffer from multiple reflections, which are orientation, environment and time dependent. · The best performance is achieved with a short cable between the antenna and the wireless device. The shortest approved cable to be used in conjunction with the ANT24D18 in North America is the NETGEAR 1. 5 m (ACC-10314-01) cable. The antenna should be installed so that it is a minimum of 50 cm (20 inches) away from people. 2 · · Installing the 18 dBi Patch Panel Directional Antenna There are two parts to the wireless antenna installation process: Mount the antenna on a pole, or on a wall with adjustable brackets, or on a wall with fixed brackets. Connect the appropriate electrical hardware depending on if the installation is indoors or outdoors. · Follow the instructions in this section of the manual to install your antenna. First, Mount the Antenna Pole Mount Installation bracket B washer bolt tube washer screw nut screw screw tube screw nut bracket A washer 6 7 Wall Mount with Adjustable Bracket 2 plastic screws Now, Connect the Antenna The instructions below cover outdoor and indoor installations. bracket B 2-screw tube washer screw nut Connecting the Antenna for an Outdoor Installation 1. Connect the provided 2-meter cable to the antenna and to the arrestor as shown here. You can connect the cable to either of the two RF ports on the lightning arrestor. Wireless unit's DC block 18 dBi Patch Panel Directional Antenna ANT24D18 screw screw tube screw nut bracket A washer Wireless unit N/SMA adapter Wall Mount with Fixed Bracket 5-12V DC RESET ETHERNET Lightning arrestor 2m cable (provided) Ethernet (CAT 5) cable NETGEAR cable ACC-10314-01, 02, 03, 04, 05 (Sold separately) Ground cable (Not provided) Building grounding 3. Connect the grounding cable (not included) from the lightning arrestor to the ground of the building. Grounding cable: The grounding cable must be equivalent or better than: AWG 10, UL 1015, Stranded, 600 V, 105°C, green or green/yellow insulation, 2 clip of 5. 5 mm inner diameter cramped at both ends, cable no longer than 5 meters. Warning: the lightning arrestor and appropriate ground cable must be used for outdoor installation. NETGEAR does not assume any responsibility in case of hazard resulting of non-compliance with these instructions. 4. Screw the N/SMA Reverse Adapter on the lightning arrestor (clockwise) on the second RF port. Connect a NETGEAR cable model ACC-10314-01, 02, 03, 04 or 05 (sold separately) to the adapter. Remove the antenna and connect the other end of the NETGEAR cable ACC-10314-01, 02, 03, 04 or 05 to this port. 5. 8 9 Note: On access points with two antennas, if you are only replacing one antenna, be sure to replace the primary antenna and do not remove the secondary antenna. If connecting 2 ANT24D18 antennas: repeat step 2 to 5 for the second antenna and connect it the secondary port. If the wireless device supports transmit/receive on both ports, the 2 antennas can be used to cover 2 separate or partial overlapping WLAN areas. For instance the 2 ANT24D18 could be oriented at 90 degrees and positioned 50 feet away and using the WG302 access point. If the wireless device transmits only with the primary antenna port, the 2 ANT24D18 antennas can be used only for spatial diversity. Spatial diversity: place the 2 antennas 3 to 9 feet away and oriented toward the same direction. After attaching your new 18 dBi antenna(s), reconnect your wireless device to the network and turn it on. 4. Locate the primary detachable antenna of the wireless device. Remove the antenna and connect the other end of the NETGEAR cable ACC-10314-01, 02, 03 or 04 to this port. Note: On access points with two antennas, if you are only replacing one antenna, be sure to replace the primary antenna and do not remove the secondary antenna. 5. If connecting 2 ANT24D18 antennas: repeat step 2 to 4 for the second antenna and connect it the secondary port. If the wireless device supports transmit/receive on both ports, the 2 antennas can be used to cover 2 separate or partial overlapping WLAN areas. [. . . ] In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 50 cm (20 inches) during normal operation. This device should not be co-located with other transmitters. European Emission Statement For EU, use of any antenna requires careful planning and extra consideration to comply with EU emissions, health standards and regulations. It is recommended that a qualified professional installer service is consulted for site survey and proper installation. Antenna installation must comply with the maximum level authorized by each country. [. . . ]