User manual NETGEAR AGM721F

[. . . ] Microsoft, Windows, Windows NT and Vista are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer It is hereby certified that the AGM721F Wireless Cable Modem Gateway has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. Bestätigung des Herstellers/Importeurs Es wird hiermit bestätigt, daß das AGM721F Wireless Cable Modem Gateway gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. [. . . ] The default lease pool end IP addresses are as follows: ­ Netgear_1: 192. 168. 1. 99 ­ Netgear_2: 192. 168. 2. 99 ­ Netgear_3: 192. 168. 3. 99 Lease Time. To configure the security options, see "How to Configure Wireless Security for a Wireless Guest Network" on page 2-17. " Note: NETGEAR strongly recommends that you change the default guest network name (SSID) from the default name to a different name. You can now change the Guest Network Name (SSID) for the selected guest network. For the selected guest network, the same name must be assigned to all wireless devices in your network. After you have changed the name, click Apply again to activate the new name. 2-16 v1. 1, May 2009 Wireless Configuration Wireless Cable Modem Gateway AGM721F User Manual How to Configure Wireless Security for a Wireless Guest Network Note: To restore all guest network settings, including the wireless security settings, to their default settings, click Restore Guest Network Settings. After you have completed step 5 in the previous section, the screen expands and the security options for the guest network display. Figure 2-9 Wireless security is disabled by default. NETGEAR strongly recommends that you implement wireless security for the guest network. To configure wireless security for the guest network that you selected, enter the security options, and then click Apply to save your changes. This process is very similar to configuring wireless security for the gateway. For more information, see "Configuring WEP (Wired Equivalent Privacy) Wireless Security" on page 2-6 and "Configuring WPA or WPA2 Wireless Security" on page 2-8. Wireless Configuration v1. 1, May 2009 2-17 Wireless Cable Modem Gateway AGM721F User Manual Configuring Wi-Fi Multimedia Wi-Fi Multimedia (WMM), also referred to as Wireless Multimedia, is a subset of the 802. 11e standard. WMM allows wireless traffic to have a range of priorities, depending on the kind of data. You can add devices to the access list using either one of the following methods: · · If the computer is in the Connected Wireless Devices table, click the radio button of that computer to capture its MAC address. Enter the MAC address of the device to be added in the Add Access Filter fields. The MAC address can usually be found on the bottom of the wireless device. Note: If no Device Name appears when you enter the MAC address, you can type a descriptive name for the computer that you are adding. Now, only devices in the Access List table will be allowed to wirelessly connect to the gateway. 2-20 v1. 1, May 2009 Wireless Configuration Chapter 3 Content Filtering and Firewall Rules This chapter describes how to use content filtering and firewall rules for the gateway. Note: Log in to the gateway using its default address of http://192. 168. 0. 1 or at whatever IP address the unit is currently configured. To access the content filtering features you must log in to the gateway with the mso user name and its default password changeme, or whatever new password you have set up. This chapter includes: · · · "Configuring Logs" on this page "Blocking Keywords, Sites, and Services" on page 3-2 "Firewall Rules--Port Forwarding and Port Blocking" on page 3-5 Configuring Logs A log is a detailed record of the Denial of Service (DoS) attacks directed at your network. You can use e-mail notification to receive these logs in an e-mail message. If you do not have e-mail notification set up you can connect to the gateway to view the logs. The Logs screen displays. Figure 3-1 3-1 v1. 1, May 2009 Wireless Cable Modem Gateway AGM721F User Manual 2. [. . . ] Additionally, your PC may not have the gateway configured as its TCP/IP gateway. If your PC obtains its information from the gateway by DHCP, reboot the PC and verify the gateway address. See the link to the online document "ITCP/IP Networking Basics" in Appendix B. Troubleshooting a TCP/IP Network Using a Ping Utility Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet to the designated device. Troubleshooting a TCP/IP network is made easier by using the ping utility in your PC or workstation. Testing the LAN Path to Your Gateway You can use ping to verify that the LAN path to your gateway is set up correctly. [. . . ]