User manual NEFF T4543N1

[. . . ] ES Instrucciones para el uso 3 EN Instruction manual 39 EL Ïäçãßåò ÷ñÞóçò 70 . Table of contents Important information . Only after read ing these will you be able to operate the appliance correctly. If the appliance is passed to another per son, please enclose the instructions. Before switching on your appliance Transport damage Check your appliance after removing the packaging. If it has suffered any damage during transport, do not connect the appliance but contact the Technical Ser vices department. [. . . ] 23 45 45 45 6 7* 45 45 45 15 30 mins 25 35 mins 30 35 mins 15 25 mins 10 20 mins 6 10 mins 50 60 mins 60 100 mins 50 60 mins 1 2 pieces 2 3 pieces 10 pieces 1 1 1 1 2 mins 2 mins 2 mins 2 mins 6 6 7 6 7 7 8 7 Constant frying 6 10 mins 8 12 mins 8 10 mins 8 13 mins 8 13 mins 8 9* 4 5* constant deep fat frying constant deep fat frying 54 Tips on saving energy The correct saucepan size Use saucepans and pots with thick, even bases. The diameter of the bases of the saucepans and pots should match the size of the hotplate. Note: Ovenware manufacturers often give the diameter of the top of the saucepan. A larger, less full saucepan requires more energy. Using a lid Saucepans and pots should always be covered with a suitable lid. Cook with small quantities of water This saves energy and helps vegetables to retain vitamins and minerals. Switch down to a lower heat setting in good time. Cooking with small quantities of water Lowering the heat setting Keep warm function All induction hotplates have the keep warm function. Method of operation The keep warm function is suitable for melting chocolate or butter or keeping food warm. This only works with pots and pans suitable for use with induction hobs. If the "keep warm" function is activated, the hotplate automatically changes to its minimum power setting to keep cookware warm. The letter C appears in the visual display. 55 How to deactivate it Follow these steps: 1. The C disappears in the visual display and the function will have been deactivated. Powerboost function Use this function to heat up the contents of the pan faster than if you use the maximum power level (j). This function allows you to increase the maximum power level of the hotplate in use. Powerboost function limitations Group 2 All the cooking zones have this function, except the roasting zone when its expandable part is activated. (See figure, zone 5) Group 1 Group 2 The Powerboost function will always be available whenthe other hotplate of the same group is not switched on. (See illustration) For example, if you want to activate this function in hotplate 1, number 2 (situated behind it) should be switched off, and vice versa. If the zone referred to is not switched off, the letter x and the power level j in the hotplate indicator will flash; it will return to the maximum power level setting (j). The same applies to hotplates 3 and 4. Group 1 56 How to activate it The hotplate must be connected. 1. Select the hotplate desired using the control knob. k will flash on the indicator. Press the sensor P, and the letter x will appear on the display. This is how to deactivate it Follow these steps: 1. The letter x will disappear from the display and the hotplate will return to the heat level j. d Timer function In certain circumstances, the Powerboost function may be deactivated automatically to protect the internal electronic components of the hob. The timer is an electronic clock. This means that it can still be set when the hob is locked. Setting a hotplate to switch off automatically Enter a specific duration for the desired hotplate. When the duration has elapsed, the hotplate switches off automatically. 57 Setting procedure The hotplate must be switched on. 1. The duration flashes for several seconds and then begins to count down. If you have set a duration for several hotplates, it is always the shortest duration that is displayed. When the duration has elapsed When the duration has elapsed, the hotplate switches off. [. . . ] If the symbol continues to appear contact the technical assistance service. F2 it is turned off by touching the control surface if the hob has cooled down sufficiently. If after connection F4 appears again, call the technical assistance service. To continue cooking touch any sensor. F display and numbers Visual indication F0 Fault An internal error was produced while the hob was working. F2 The cooking hob is too hot and has turned off. [. . . ]