User manual NEFF T29R96N0AU

[. . . ] This cooktop is for use with Natural Gas and LPG T29R8N0AU T29R96NOAU Neff GmbH Carl-Wery-Straße 34 81739 München Cod. 9000235447 C Dear customer, We would like to thank and congratulate you for your choice. This practical modern appliance has been made using materials of the highest quality, which have been put through the strictest of Quality Controls during manufacture and meticulously tested to ensure that they meet all of your cooking demands. We kindly ask you to read and follow these simple instructions in order to guarantee first-class results from the very start. [. . . ] When connecting the cooktop ensure that the earth wire is connected first and that all wires are connected to the correct terminals. Gas: During the planning stage, consider the position of supply connections. The hob must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid regulations. We recommend that the isolation valve be fitted prior to the cooktop to enable isolation of cooktop from gas supply. To find out the factory set gas type, see bottom of cooktop next to gas connection. Fit regulator (N. G. ) or a test point (LPG) directly to the R1/2" connection as per Fig. Use pipe compound or thread sealant, properly theaded pipes and careful assembly procedure so that there is no cross threading, etc. , which might cause damage or leakage. The manufacture does not accept any liability for leakage on connections performed by the installer or if the L-tube is moved or twisted. Natural gas connection LPG connection Pressure test point R 1/2" Gasket R 1/2" Gasket Pressure test point. 5 9 6 There are two ways to carry out the connection to the main gas line: A. The hotplate can be connected with rigid pipe as specified in AS5601 table 3. 1. Flexible Hose: If installing with a hose assembly, install with a hose assembly that complies with AS/NZS 1869 (AGA Approved), 10mm ID, class Bor D, no more than 1, 2m long and in accordance with AS5601. Ensure that the hose does not contact the hot surfaces of the hotplate, oven, dishwasher or any other appliance that may be installed underneath or next to the hotplate. The hose should not be subjected to abrasion, kinking or permanent deformation and should be able to be inspected along its entire length with the cooktop in the installed position. Unions compatible with the hose fittings must be used and all connections tested for gas leaks. NOTE: it is not necessary to adjust the primary air control on these burners. 7 mm 6 7 8 11 Minimum flame adjustment. If your cooking hob is fitted with exterior plastic disc seals, remove them by inserting a screwdriver through the disc's central orifice and levering them out. When you have removed the disc seals from the orifice the control shaft emerges from, you will find an interior seal made of flexible rubber; you only need to press this with the tip of a screwdriver to clear the path to the tap adjusting screw. 4 The adjustment screw is positioned at the rear lower section of the valve. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. Screw the adjustment screw anti-clockwise to estabilish a minimum stable flame position. The flame should remain alight and not burn back to the injector when the valve is turned quickcly from `Full On' to the "Minimum flame" position and back a few times. To adjust the minimum flame position for LPG the screw must be fully tightened down clockwise. Never dismount the valve shaft: in the event of damage, change the entire valve. 9 10 11 12 Operating instructions Burner locations 2 1 1 3 3 4 2 12 1. [. . . ] Avoid Knocking any part of the edge of the cooking plate. DOs Once the appliance is cold, clean it with a sponge and soapy water. Clean the surface of the heating elements once they have cooled down, each time they are used. Even small amounts of dirt burn when it is switched on again. The burners and pans support must be cleaned regulary to keep them clean. This is done by submerging them in soaply water and scrubbing them them with a non-metal brush to keep the holes and slits free from obstruction so they can give a perfect flame. [. . . ]