User manual NEFF S59T45X0EU

[. . . ] 9000 249 731 (9009) HQ 2SHUDWLQJ LQVWUXFWLRQV Q en Table of contents Washing the dishes . 15 15 15 15 16 16 16 16 16 17 17 17 17 18 18 18 18 19 19 20 20 20 21 21 22 23 23 23 24 24 24 24 25 25 25 25 26 26 26 Safety instructions . 15 en Safety instructions Delivery ­ Check the packaging and dishwasher immediately for damage caused in transit. ­ Please dispose of the packaging material in an environmentally friendly manner. [. . . ] The programme starts running. 15 en Optical display while the programme is running * * depending on model While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. End of programme The programme has ended when the value is indicated on the numerical display @. The programme button 3 flashes and the factory-set value (half-loud) lights up on the numerical display @. Each time the button is pressed, the set value increases by one level; when the value of has been reached, the display jumps back to (off). ­ Close the door. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display @. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming * * depending on model You can delay the start of the programme in 1 hour steps up to 19 hours. ­ Press the timer programming button 8 until the digital display @ jumps to . ­ Keep pressing the timer programming button 8 until the required time is displayed. ­ To delete the preselected starting time, press the button 8 until is indicated on the digital display @. You can change your programme selection at any time until the programme starts. Switching off the appliance Short time after the end of the programme: ­ Open the door. ­ Remove the utensils when they have cooled down. 16 en ã=Warning Changing the programme After you have switched the appliance on, it is possible to change the programme within 2 min. If you want to change the programme afterwards, the appliance waits until the initiated programme section (e. The remaining time comprises the remaining time of the previous programme section and the remaining time of the new selected programme. At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme ­ Open the door. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. ­ Close the door. Intensive drying The final rinse uses a higher temperature which improves the drying result. ­ Hold down programme button # and press main switch ( until the digital display illuminates. The LED for button # flashes and the digital display @ displays the setting (off) or (on). To change the setting: ­ By pressing the # button, you can switch intensive drying on or off . ­ Close the door. Terminating the programme (Reset) ­ Open the door. [. . . ] temperature 60 °C. Waste-water connection ­ The required work sequence can be found in the installation instructions. ­ Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts. Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out! Fresh water connection ­ Connect the fresh-water connection to the tap according to the installation instructions with the enclosed parts. Ensure that the fresh-water connection is not kinked, crushed or twisted. [. . . ]