User manual NEFF S44E33

[. . . ] D The wooden frames (if fitted) are made of residual wood and are untreated. Built-under and built-in appliances should always be installed under a continuous work surface which is attached to the adjacent cupboards, in order to ensure that the appliance is entirely stable. After the appliance has been installed, the mains plug should still be easily accessible. Not on all models: The plastic housing on the water input contains an electrically operated valve. [. . . ] If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. limescale forms. If you are using detergent in tablet form, read the manufacturer's recommendations on the packaging in order to determine where the tablets should be placed inside the dishwasher (e. g. Make sure that the lid on the detergent compartment is closed, even if you are using tablets. 15 en Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. Note Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runs correctly when 3in1 products are used. If the rinse aid refill indicator 7 or salt refill 6 indicator is defective and you would like to switch it off, proceed as follows: Switch on main switch 1 and hold down for at least 3 sec. The digital display 8 indicates the current set hardness value and the salt refill indicator 6 flashes (hardness value has been set to 4 at the factory). You can select a set value between 0 and 7 according to the hardness of your water. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. Switching the salt refill indicator / water softening system off and on Close the door Rotate the programme selector 3 from the 12 o'clock position by one notch to the left. Switching the rinse-aid refill indicator off or on* * some models You can switch off the rinse-aid refill indicator 7 if you use a detergent with integrated rinse-aid. The digital display 8 indicates (rinse-aid refill indicator) and the button A flashes. By pressing button A you can switch the rinse-aid indicator off or on . The programme sequence starts automatically. Changing the programme It is possible to change the programme within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e. g. The new remaining time displayed is the sum of the remaining time from the preceding programme cycle and the remaining time attributable to the new programme that has been selected. 19 en Additional functions * on some models additional functions 4 Washing contents of LOWER RACK only * If you have a small number of dishes to wash in the lower rack (e. g. Add a reduced amount of detergent compared to that which is recommended for a full load. can be set with the buttons. Pre-Soak * The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. If you wish to pre-soak the dishes, this programme option must be selected by pressing the "Pre-Soak" button before the programme starts. 5 g poured onto the inside of the door. Time delay * h. Time reduction/ time saving * Pressing the "Time reduction/time saving" button provides a short wash cycle by curtailing the drying phase and the washing time. The washing and drying performance will be reduced with the Time reduction/time saving programme option. Washing contents of UPPER RACK only * If you have a small number of dishes to wash in the upper rack (e. g. Add a reduced amount of detergent compared to that which is recommended for a full load. You can delay the start of the programme in 1-hour steps up to 19 hours. Press the timer programming button until the digital display 8 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer programming, keep pressing the button until is displayed. [. . . ] If you do use hot water, the temperature should not exceed 60 °C. Delivery Your dishwasher was checked at the factory to ensure that it was in perfect working order. These will disappear after the first rinse cycle. Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed socket with protective conductor. The socket must be attached near the dishwasher and be freely accessible. Use only a residual-current-operated circuit-breaker which features the symbol. [. . . ]