User manual NEFF S4409N1GB

[. . . ] de Gebrauchsanweisung de Gebrauchsanweisung 9000 040 728 (8402) en Instructions for use en Index 4 6 7 8 9 10 11 12 15 17 serve@Home * . Selecting options/standard settings Information about programme sequence . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Please dispose of packaging material properly: D The corrugated cardboard consists mainly of waste paper. [. . . ] Keep pressing button M/OK 2 until the "rinse aid 4" setting is displayed. By pressing buttons ­ or + 3 , you can select a set value between 0 and 6. If the set value "0" is selected, rinse aid is not dispensed. Low rinse aid is not displayed. 20 en Programme overview Type of utensil e. g. Type of food remains e. g. Hardwearing Mixed Fragile Mixed Soups, soufflés, sauces, potatoes, pastries, rice, eggs, fried food Soups, potatoes, pastries, rice, eggs, fried food Coffee, cake, milk, sausage, cold drinks, salads Rinse if the utensils have been left for several days prior to washing in the dish washer Amount of food remains Condition of food remains Very adhesive Large -> small Slightly adhesive Very small Wash programme AUTO SUPER WASH 60° ­ 70° AUTO WASH 45° ­ 55° AUTO DELICATE WASH 35° ­ 45° QUICK WASH 45° PRERINSE ONLY Programme progress Prerinse The programme progress is optimised and adjusted according to the appliance load and degree of soiling on the utensils. Clean Intermediate wash Final wash Drying 21 en Programme data The programme data (duration, energy and water consumption) can be found in the summary of instructions and refers to standard conditions. Greater deviations may be caused by: different quantities of utensils inlet temperature of the water water pressure ambient temperature mains voltage tolerances and appliance-specific tolerances (e. g. temperature, water flow rate, etc. ) Only ranges can be indicated for the automatic programmes. The water consumption values refer to water hardness value 4. Selecting options/ standard settings Operating principle From the Main Menu you can select the following options/settings by repeatedly pressing the button M/OK 2 : Time Pre-select Remote Control ** Reduce Time Drying Level Buzzer Volume Adding Rinse Aid Water Hardness Language Standard Programmes Remote Setting ** ** Only with installed serve@Home interface Within an option/basic setting there are several possible settings that can be selected using the buttons ­ or + 3 . A selected setting is applied by changing to the next option/basic setting using the button M/OK 2 . If a setting has been changed using the buttons ­ or + and stored using M/OK 2 , the message "Value stored" will be displayed and the display returns to the Main Menu. 22 en Time Pre-select You can delay the programme start by 24 hours in steps of 30 minutes. If the option "Time Pre-select" is chosen the display shows "Delay Start: 00 mins". Return to the Main Menu by pressing M/OK 2 and start the required programme by pressing the Start Button 5. Until the programme starts you are able to change the set time and programme. To do this, use the button ­ 3 to return to the Main Menu and change the settings. In order to delete the pre-selected time, set the time back to "Delay Start: 00mins". Reduce Time The Auto Programmes allow you to reduce the run time of the programmes. However, in order to achieve an optimal cleaning result, the water and energy consumption will be increased. If the option "Reduce Time" is chosen the display shows "Reduce Time: Off" (factory setting). Return to the Main Menu by pressing M/OK 2 and start the required programme by pressing the Start Button 5. If you do not want to use "Reduce Time" the next time you use the dishwasher, you must deselect this option. Drying Level If the option "Drying Level" is chosen the display shows "Normal Drying" (factory setting). Alternatively, you can choose "Save Drying" or "Extra Drying". The option "Extra Drying" increases the temperature during rinsing in all programmes. [. . . ] Using the height-adjustable feet, adjust the appliance until it is level. Ensure that the appliance is standing firmly. Waste water connection See the installation instructions for the required connection steps. Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. Ensure that the drainage hose is not kinked, crushed or twisted (ensure that there is no sealing cover which prevents the waster water from flowing away!). 36 en Fresh water connection Using the enclosed parts, connect the fresh water connection to the tap according to the installation instructions. [. . . ]